Table of Content:
1 Introduction
1.1 Foreword
1.2 John Deere Technical Information Bookstore
2 Safety
2.1 Recognize Safety Information
2.2 Understand Signal Words
2.3 Follow Safety Instructions
2.4 Practice Safe Maintenance
2.5 Use Steps and Handholds Correctly
2.6 Handle Electronic Components and Brackets Safely
2.7 Use Electronic Display Properly
2.8 Operate Guidance Systems Safely
2.9 Use Seat Belt Properly
2.10 Operate Implement Automation Systems Safely
2.11 Avoid High-Pressure Fluids
3 Regulatory and Compliance Information
3.1 Identify Date Code
3.2 Eurasian Economic Union – EAC
3.3 EU Declaration of Conformity
3.4 UK Declaration of Conformity
4 System Overview—iGrade™
4.1 Theory of Operation—iGrade™
4.2 Grade Control
4.3 Plane Control
4.4 Remote Control
4.5 Origin Point
4.6 Satellite Information—VDOP
4.7 Surface Maps
5 System Overview—Distance Trip
5.1 Theory of Operation—Distance Trip
5.2 Parallel Lines
5.3 Fence Post
5.4 Grid
5.5 Plot Pattern
5.6 Satellite Information—PDOP
6 System Overview
6.1 Requirements
6.2 Navigate to Application Controller Pages
6.3 Navigate to StarFire™ Pages
6.4 Enter Activation Code
6.5 Replace Erasable Programmable Read-Only Memory (EPROM)
6.6 Machine Compatibility
7 Component Overview
7.1 StarFire™ Receiver
7.2 StarFire™ Global Navigation Satellite System (GNSS) Antenna (Recommended)
7.3 Choke Ring Antenna (Optional)
7.4 Display
7.5 UCC2 Application Controller
7.6 Counterbalance Valve
7.7 External Valve
8 Assembly
8.1 Message Definition
8.2 Remote Control Serial Port Hardware
8.3 Distance Trip Low Side Driver
8.4 Implement Operator’s Station
9 Setting Up—Equipment
9.1 Connect Implement
9.2 Adjust Selective Control Valve (SCV)
9.3 Adjust Counterbalance Valve
9.4 Set Up Base Station
9.5 Set Up Global Position System (GPS) Receiver
9.6 Optimize Terrain Compensation Module (TCM)
9.7 Calibrate Terrain Compensation Module (TCM)
10 Setting Up—UCC2 Application Controller
10.1 Setup Wizard Overview
10.2 Serial Ports
10.3 Set Up Run Page
11 Setting Up—iGrade™
11.1 GPS Offsets
11.2 SCV Configuration
11.3 Manual SCV Calibration
11.4 Surface
11.5 Elevation Offset
11.6 Edit Control Sensitivity
11.7 Load Limiting
11.8 Edit Load Limiting Sensitivity
11.9 Maximum Cut
12 Setting Up—Distance Trip
12.1 Equipment Offsets
12.2 Trip Pattern
12.3 Trip Command
12.4 Trip Documentation
12.5 Enable File Server
12.6 Equipment Offset Calibration
12.7 Trip Action Test
12.8 Equipment Delay Calibration
13 Operating
13.1 Engage Auto Mode
13.2 Disengage, Deactivate, and Disable Implement Automation
13.3 SCV Command Control
13.4 Status Tab
13.5 Operate Distance Trip
13.6 Operate iGrade™—Plane Control and Remote Control
13.7 Operate iGrade™—Grade Control
14 Troubleshooting
14.1 Reset UCC2 Application Controller
14.2 Status and Exit Codes
14.3 Troubleshooting—Distance Trip System
14.4 Troubleshooting—iGrade™ System
14.5 Troubleshooting—Machine
14.6 External Valve
14.7 Data Cleanup
14.8 Clean Up ISOBUS VT
14.9 Diagnostics—Distance Trip Status
14.10 Diagnostics—iGrade™ Status
14.11 Diagnostics—Setpoints
14.12 Diagnostics—Maximum Cut
14.13 Diagnostics—Load Limiting
14.14 Diagnostics—Remote Control
14.15 Hardware/Software
14.16 Input/Output Readings
14.17 Hours
14.18 SCV Diagnostics
15 Maintenance
15.1 Preseason Checklist
15.2 Daily Checklist
15.3 Postseason Checklist
16 Index
17 John Deere Service Literature Available
17.1 Technical Information
18 John Deere Service Keeps You on The Job
18.1 John Deere Is At Your Service