Table of Content:
1 Introduction
1.1 Foreword
1.2 Emissions Performance and Tampering
2 Glossary
2.1 Glossary
2.2 Trademarks
3 Safety
3.1 Recognize Safety Information
3.2 Understand Signal Words
3.3 Follow Safety Instructions
3.4 Prepare for Emergencies
3.5 Wear Protective Clothing
3.6 Protect Against Noise
3.7 Handle Fuel Safely?Avoid Fires
3.8 Handle Starting Fluid Safely
3.9 Fire Prevention
3.10 In Case of Fire
3.11 Avoid Static Electricity Risk When Refueling
3.12 Keep ROPS Installed Properly
3.13 Use Foldable ROPS and Seat Belt Properly
3.14 Stay Clear of Rotating Drivelines
3.15 Use Steps and Handholds Correctly
3.16 Read Operator?s Manuals for ISOBUS Controllers
3.17 Use Seat Belt Properly
3.18 Operating the Tractor Safely
3.19 Avoid Backover Accidents
3.20 Limited Use in Forestry Operation
3.21 Operating the Loader Tractor Safely
3.22 Keep Riders Off Machine
3.23 Instructional Seat
3.24 Use Safety Lights and Devices
3.25 Use a Safety Chain
3.26 Transport Towed Equipment at Safe Speeds
3.27 Use Caution on Slopes, Uneven Terrain, and Rough Ground
3.28 Freeing a Mired Machine
3.29 Avoid Contact with Agricultural Chemicals
3.30 Handle Agricultural Chemicals Safely
3.31 Handling Batteries Safely
3.32 Avoid Heating Near Pressurized Fluid Lines
3.33 Remove Paint Before Welding or Heating
3.34 Handle Electronic Components and Brackets Safely
3.35 Practice Safe Maintenance
3.36 Avoid Hot Exhaust
3.37 Clean Exhaust Filter Safely
3.38 Work In Ventilated Area
3.39 Support Machine Properly
3.40 Prevent Machine Runaway
3.41 Park Machine Safely
3.42 Transport Tractor Safely
3.43 Service Cooling System Safely
3.44 Service Accumulator Systems Safely
3.45 Service Tires Safely
3.46 Service Front-Wheel Drive Tractor Safely
3.47 Tightening Wheel Retaining Bolts/Nuts
3.48 Avoid High-Pressure Fluids
3.49 Do Not Open High-Pressure Fuel System
3.50 Store Attachments Safely
3.51 Decommissioning ? Proper Recycling and Disposal of Fluids and Components
4 Safety Signs
4.1 Use the Seat Belt
4.2 Operate the Tractor Safely
4.3 Do Not Modify ROPS
4.4 Use of Instructional Seat (If Equipped)
4.5 Tow Trailer Safely (Not on Tractors up to 30 km/h)
4.6 Caution When Operating Front Loader (on Tractors with Mechanical Selective Control Valves)
4.7 Caution When Operating Front PTO
4.8 Caution When Operating Rear PTO
4.9 Pressure Accumulator (Front Hitch, for Tractors without Suspended Front-Wheel Drive Axle)
4.10 Pressure Accumulators (Suspended Front-Wheel Drive Axle, If Equipped)
4.11 Pressure Accumulators (Suspended Front-Wheel Drive Axle, If Equipped)
4.12 Pressure Accumulator (Brake System)
4.13 Electrical Coolant Heater of Engine (If Equipped)
4.14 .
5 Vehicle Overview
5.1 Identification Views
5.2 Identification Views
6 Operator’s Manual ? General Information
6.1 Scope of This Manual
6.2 How to Use This Manual
6.3 Comply with Operator’s Manuals of Implement Manufacturers
7 Operating the Engine
7.1 US EPA Qualified Emergency Use ? SCR Derate Override Option
7.2 Important Engine Information
7.3 Engines with Turbocharger
7.4 Engine Protection
7.5 Required Machine Stop Warning
7.6 Engine Menu
7.7 Check Engine Indicator Lights and Displays
7.8 Intelligent Power Management (Power Boost)
7.9 Starting the Engine
7.10 Engine Start with an Auxiliary Battery
7.11 Shutting Off the Engine
7.12 Battery Disconnect System (If Equipped)
7.13 Park the Tractor with PowrQuad?/AutoQuad? PLUS
7.14 Park the Tractor with CommandQuad? PLUS
7.15 Park the Tractor with AutoPowr?/IVT?
7.16 Tow-Starting
7.17 Fill the Fuel Tank
7.18 Fill the DEF Tank
8 Cold-Weather Operation
8.1 Cold Start Aids
8.2 Coolant Heater
8.3 Ground Fault Circuit Interrupter (GFCI)
9 Aftertreatment
9.1 Exhaust Filter Cleaning, General Information
9.2 Required Machine Stop Warning
9.3 Aftertreatment Indicators Overview
9.4 Access the Engine Menu
9.5 Exhaust Filter Cleaning Overview
9.6 DEF (Diesel Exhaust Fluid) Level Gauge
9.7 Selective Catalytic Reduction (SCR) System Overview
10 Operator Controls
10.1 Controls in the Side Console, Overview
10.2 Vehicle Controls with PowrQuad? PLUS and AutoQuad? PLUS Transmissions
10.3 Vehicle Controls with CommandQuad? PLUS Transmission without CommandARM?
10.4 Vehicle Controls with CommandQuad? PLUS Transmission with CommandARM?
10.5 Vehicle Controls with AutoPowr? Transmission without CommandARM?
10.6 Vehicle Controls with AutoPowr? Transmission with CommandARM?
10.7 Key Switch
10.8 Come-Home Mode
10.9 Immobilizer
10.10 Creeper – Controls
10.11 PTO – Controls
10.12 Economy Front Hitch – Controls
10.13 Rear Hitch – Controls
10.14 Mechanical Selective Control Valves – Controls
10.15 Electronic Selective Control Valves – Controls
10.16 Mechanical Joystick
10.17 Electric Joystick
10.18 Front-Wheel Drive – Controls
10.19 Differential Lock – Controls
10.20 iTEC? Basic ? Intelligent Total Equipment Control – Controls
10.21 AutoTrac? – Controls
10.22 ISOBUS Button (ISB)
10.23 Heating, Ventilation and Air-Conditioning System – Controls
10.24 Radio A?Additional Phone Controls
11 Corner Post Display
11.1 Corner Post Display
11.2 Warning Indicators
11.3 Digital Indicators ? Revolution Counter, Ground Speed, Transmission, and Set Speed
11.4 Gauges – Coolant Temperature, DEF Level, and Fuel Level
11.5 Overview of All Menus
11.6 Basic Menu Navigation
11.7 Information Display, Run Pages
11.8 Display Settings, Menu
11.9 Display Settings, Brightness
11.10 Display Settings, Display Modes (Day/Night)
11.11 Display Settings, Language
11.12 Display Settings, Units
11.13 Display Settings, Numeric Format
11.14 Display Settings, Information on the Corner Post Display
11.15 Work Monitor, Menu
11.16 Work Monitor, Counters A and B
11.17 Work Monitor, Readings
11.18 Work Monitor, Implement Width
11.19 Work Monitor, Recording Trigger
11.20 Layout Manager, Settings
11.21 Set up Controls
12 CommandARM? Controls
12.1 CommandARM?, Controls (with CommandQuad? Plus)
12.2 CommandARM?, Controls (with AutoPowr?/IVT?)
13 Radio A Operation
13.1 Radio A?Controls and Instruments
13.2 Radio A?Additional Phone Controls
13.3 Radio A?Microphone for Bluetooth Applications
13.4 Radio A?Connection of Memory Storage and Multimedia Appliances
13.5 FM, MW, LW and DAB/DAB+-Compliant Radio Antenna (Europe Only)
14 Radio B Operation
14.1 Radio B?Identification Views and Features
14.2 Radio B?Controls and Instruments
14.3 Connection of Memory Storage and Multimedia Appliances
14.4 FM, MW, LW and DAB/DAB+-Compliant Radio Antenna (Europe Only)
15 Guidance
15.1 AutoTrac? Guidance System (If Equipped)
15.2 AutoTrac? Guidance with GreenStar? Display
15.3 AutoTrac? Basic Guidance with Corner Post Display
15.4 Operate Guidance Systems Safely
15.5 Enable AutoTrac? Basic
15.6 Disable AutoTrac? Basic
15.7 AutoTrac? Resume Switch
15.8 Activate AutoTrac? Basic
15.9 Disengage AutoTrac? Basic
15.10 Reactivate AutoTrac? Basic on Next Pass
15.11 AutoTrac? Basic Menu
15.12 AutoTrac? Basic Map
15.13 AutoTrac? Status Pie
15.14 AutoTrac? Basic Track Setup
15.15 AutoTrac? Basic Tread Width
15.16 AutoTrac? Basic Shift Size
15.17 AutoTrac? Basic Vehicle
15.18 AutoTrac? Basic Tuning
15.19 StarFire? Correction Mode
15.20 AutoTrac? Basic TCM Calibration
15.21 StarFire? USB Drive
15.22 StarFire? GPS Status
15.23 AutoTrac? Basic Settings Locked
15.24 AutoTrac? Basic About
15.25 GPS Receiver Offset Values
15.26 AutoTrac? Universal Information
16 Intelligent Total Equipment Control (iTEC?)
16.1 iTEC? Basic, General Information
16.2 Basic Menu Navigation
16.3 iTEC? Basic, Menu
16.4 iTEC? Basic, Access Functions
16.5 iTEC? Basic, Settings
17 Drivetrain
17.1 Drive Systems – Overview
18 Front-Wheel Drive
18.1 Front-Wheel Drive, Control Elements and Indicator Lights
18.2 Front-Wheel Drive, Manual Engagement and Disengagement
18.3 Front-Wheel Drive, Automatic Engagement and Disengagement
18.4 Tractor Equipped With Front Suspension Option
19 Differential Lock
19.1 Differential Lock, Controls and Indicator Lights
19.2 Differential Lock, Manual Engaging/Disengaging
19.3 Differential Lock, Automatic Engaging/Disengaging
20 Brakes
20.1 Hydraulic Service Brakes
20.2 Single-Line Hydraulic Trailer Brake (If Equipped)
20.3 Socket for the Anti-Lock Brake System (ABS) of Trailer
20.4 Park the Tractor with PowrQuad?/AutoQuad? PLUS
20.5 Park the Tractor with CommandQuad? PLUS
20.6 Park the Tractor with AutoPowr?/IVT?
21 Transmission – General Information
21.1 Reduce Fuel Consumption
21.2 Select Correct Ground Speed
21.3 Notes on Changing to a Different Size of Tire
21.4 Engage Creeper Transmission
21.5 Travel Speed Tables and SRI Values
21.6 Ground Speeds, PowrQuad? PLUS Transmission for 30 km/h (16/16) – Tires with SRI 700 and 725
21.7 Ground Speeds, PowrQuad? PLUS Transmission for 30 km/h (16/16) – Tires with SRI 750 and 800
21.8 Ground Speeds, PowrQuad? PLUS Transmission for 30 km/h (16/16) – Tires with SRI 825
21.9 Ground Speeds (ex Factory with Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 700 and 725)
21.10 Ground Speeds (ex Factory with Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 750 and 775)
21.11 Ground Speeds (ex Factory with Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 800 and 825)
21.12 Ground Speeds (ex Factory without Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 700, 725, 750 and 775)
21.13 Ground Speeds (ex Factory without Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 800 and 825)
21.14 Ground Speeds, CommandQuad? PLUS Transmission for 40 km/h (24/24) – Tires with SRI 700, 725, 750 and 775
21.15 Ground Speeds, CommandQuad? PLUS Transmission for 40 km/h (24/24) – Tires with SRI 800 and 825
22 PowrQuad? PLUS Transmission
22.1 PowrQuad? PLUS Transmission, Controls
22.2 PowrQuad? PLUS Transmission, Park Lock
22.3 PowrQuad? PLUS Transmission, Reverse Drive Lever
22.4 PowrQuad? PLUS Transmission, Range-Shift Lever
22.5 PowrQuad? PLUS Transmission, Gearshift Buttons
22.6 PowrQuad? PLUS Transmission, Clutch Pedal and Clutch Button
22.7 PowrQuad? PLUS Transmission, Speed Control Pedal and Hand Throttle
22.8 PowrQuad? PLUS Transmission, Engine Set Speed
22.9 PowrQuad? PLUS Transmission, Cold-Weather Operation
22.10 PowrQuad? PLUS Transmission, Come-Home Mode
22.11 PowrQuad? PLUS Transmission, Menu
22.12 Symbols in the Transmission Menu
22.13 PowrQuad? PLUS Transmission, PowrReverser?
22.14 PowrQuad? PLUS Transmission, Reverse/Forward Ratio
22.15 PowrQuad? PLUS Transmission, Backup Alarm
23 AutoQuad? PLUS Transmission
23.1 AutoQuad? PLUS Transmission, Controls
23.2 AutoQuad? PLUS Transmission, Park Lock
23.3 AutoQuad? PLUS Transmission, Reverse Drive Lever
23.4 AutoQuad? PLUS Transmission, Range-Shift Lever
23.5 AutoQuad? PLUS Transmission, Gearshift Buttons
23.6 AutoQuad? PLUS Transmission, Clutch Pedal and Clutch Button
23.7 AutoQuad? PLUS Transmission, Automatic Gear Shifting
23.8 AutoQuad? PLUS Transmission, Speed Control Pedal and Hand Throttle
23.9 AutoQuad? PLUS Transmission, Engine Set Speed
23.10 AutoQuad? PLUS Transmission, Cold-Weather Operation
23.11 AutoQuad? PLUS Transmission, Come-Home Mode
23.12 AutoQuad? PLUS Transmission, Menu
23.13 Symbols in the Transmission Menu
23.14 AutoQuad? PLUS Transmission, Transmission Mode
23.15 AutoQuad? PLUS Transmission, PowrReverser?
23.16 AutoQuad? PLUS Transmission, Reverse/Forward Ratio
23.17 AutoQuad? PLUS Transmission, Backup Alarm
24 CommandQuad? PLUS Transmission
24.1 CommandQuad? PLUS Transmission, Controls without CommandARM?
24.2 CommandQuad? PLUS Transmission, Controls with CommandARM?
24.3 CommandQuad? PLUS Transmission, Control Lever of the Park Lock
24.4 CommandQuad? PLUS Transmission, Reverse Drive Lever
24.5 CommandQuad? PLUS Transmission, Range Shift Unit
24.6 CommandQuad? PLUS Transmission, Shift Lever
24.7 CommandQuad? PLUS Transmission, Set Maximum Ground Speed
24.8 CommandQuad? PLUS Transmission, Speed Control Pedal and Hand Throttle
24.9 CommandQuad? PLUS Transmission, Engine Set Speed
24.10 CommandQuad? PLUS Transmission, Select Start Gear
24.11 CommandQuad? PLUS Transmission, Brake Pedals and Clutch Pedal (AutoClutch Function)
24.12 CommandQuad? PLUS Transmission, Special Features when Maneuvering the Tractor
24.13 CommandQuad? PLUS Transmission, Adjust Driving Characteristics
24.14 CommandQuad? PLUS Transmission, Operating with Trailer on Hillsides in Slippery Conditions
24.15 CommandQuad? PLUS Transmission, Stopping and Parking the Tractor
24.16 CommandQuad? PLUS Transmission, Come-Home Mode
24.17 CommandQuad? PLUS Transmission, Tow the Tractor
24.18 CommandQuad? PLUS Transmission, Menu
24.19 Symbols in the Transmission Menu
24.20 CommandQuad? PLUS Transmission, Start Gears
24.21 CommandQuad? PLUS Transmission, PowrReverser?
24.22 CommandQuad? PLUS Transmission, Reverse/Forward Ratio
24.23 CommandQuad? PLUS Transmission, Minimum Speed
24.24 CommandQuad? PLUS Transmission, Load Anticipation
24.25 CommandQuad? PLUS Transmission, Droop with PTO OFF/ON
24.26 CommandQuad? PLUS Transmission, AutoClutch
24.27 CommandQuad? PLUS Transmission, Backup Alarm
25 AutoPowr?/IVT? Transmission
25.1 AutoPowr?/IVT? ? Reverse Drive Lever
25.2 AutoPowr?/IVT? ? Speed Control Lever
25.3 AutoPowr?/IVT? ? Stop and Park the Tractor
25.4 AutoPowr?/IVT? ? Speed Control Pedal and Hand Throttle
25.5 AutoPowr?/IVT? ? Engine Set Speed
25.6 AutoPowr?/IVT? ? Travel Set Speed
25.7 AutoPowr?/IVT? ? Travel Set Speed, Guidelines
25.8 AutoPowr?/IVT? ? Clutch Pedal
25.9 AutoPowr?/IVT? ? Special Features when Maneuvering the Tractor
25.10 AutoPowr?/IVT? ? Downhill Braking of Tractors with Trailer
25.11 AutoPowr?/IVT? ? Using Individual Brake Pedals
25.12 AutoPowr?/IVT? ? Cold-Weather Starting
25.13 AutoPowr?/IVT? ? Come-Home Mode
25.14 AutoPowr?/IVT? ? Tow the Tractor
25.15 AutoPowr?/IVT? ? Menu
25.16 AutoPowr?/IVT? ? Symbols in the Transmission Menu
25.17 AutoPowr?/IVT? ? Transmission Mode
25.18 AutoPowr?/IVT? ? PowrReverser?
25.19 AutoPowr?/IVT? ? Reverse/Forward Ratio
25.20 AutoPowr?/IVT? ? Min RPM
25.21 AutoPowr?/IVT? ? Transmission, Load Anticipation
25.22 AutoPowr?/IVT? ? Droop with PTO OFF/ON
25.23 AutoPowr?/IVT? ? AutoClutch
25.24 AutoPowr?/IVT? ? Backup Alarm
26 PTO Shaft, Hitches, and Trailer Hitches
26.1 Hitch – Maximum Lifting Force
27 PTO Shaft – General Information
27.1 Front PTO?PTO Shield
27.2 Rear PTO?PTO Shield
27.3 Operating Instructions
27.4 PTO Speeds
27.5 PTO Options
28 Front PTO
28.1 Front PTO
28.2 Engage and Disengage the Front PTO
28.3 Front PTO ? PTO Automatic Shutoff Function
29 Rear Power Take-Off
29.1 Engage and Disengage the Rear PTO
29.2 Rear PTO – Select Standard Speed (Shiftable PTO)
29.3 Rear PTO – Remote Control and Function
29.4 Rear PTO – PTO Automatic Shutoff Function
29.5 Rear PTO – Change the PTO Stub Shaft
29.6 Rear PTO – Connect an Implement
30 Front Hitch
30.1 Economy Front Hitch – Controls
30.2 Economy Front Hitch
30.3 Front Hitch?Center Link
30.4 Front Hitch?Center Link Positions
30.5 Front Hitch?Hook-Type Center Link
31 Rear Hitch
31.1 Rear Hitch – Menu
31.2 Rear Hitch – Operation without CommandARM?
31.3 Rear Hitch – Operation with CommandARM?
31.4 Rear Hitch – Set the Depth Control Stop
31.5 Rear Hitch – Driving under Load with Mounted Implement
31.6 Rear Hitch – Hitch Dampening
31.7 Rear Hitch – Raise Height Limit
31.8 Rear Hitch – Adjust the Rate of Drop
31.9 Rear Hitch – Adjust the Raise Rate
31.10 Rear Hitch – Draft/Depth Control Adjustment
31.11 Rear Hitch – Use Draft Control
31.12 Rear Hitch – Float Position
31.13 Rear Hitch – Remote Control
31.14 Rear Hitch – Direct Actuation
31.15 Three-Point Hitch
31.16 Flat Steel Draft Links
31.17 Telescopic Draft Links
31.18 Quick-Coupling (Hook-Type) Draft Links
31.19 Attach Three-Point Hitch Mounted and Drawn Implements
31.20 Level the Implement
31.21 Center Link
31.22 Center Link Positions
31.23 Hook-Type Center Link
31.24 Hydraulic Center Link (If Equipped)
31.25 Adjust Lift Links
31.26 Lift Links – Adjust for Vertical Float
31.27 Sway Blocks, Category 2 (if Equipped)
31.28 Stabilizer Bar (If Equipped)
31.29 Stabilizing System (If Equipped)
31.30 Draft Links?Adjust Spreading Dimension
32 Trailer Hitches
32.1 Trailer Hitches?Foreword
32.2 CAT II Drawbar
32.3 Proper Use of Drawbar
32.4 Lock the Hitch Pins
32.5 Lock the Height-Adjustable Trailer Hitch
32.6 Latch for Telescopic Draft Links
32.7 Hitch Jaw
32.8 Trailer Hitch with Piton-Fix or Ball-Type (Rigid)
32.9 Height-Adjustable Ball-Type Hitch (Version 1)
32.10 Height-Adjustable Ball-Type Hitch (Version 2)
32.11 Height-Adjustable Trailer Hitch
32.12 Remote Control for Trailer Hitch (If Equipped)
33 Hydraulic System
33.1 Selective Control Valves – Maximum Permissible Oil Withdrawal
33.2 Selective Control Valves – Oil Withdrawal with Hydrostatic Drive (with PC Hydraulic System)
33.3 Selective Control Valves – Oil Withdrawal with Hydrostatic Drive (with PFC Hydraulic System)
33.4 Using Large-Volume Hydraulic Cylinders
33.5 Additional Oil Reservoir (If Equipped)
34 Hydraulic Connections
34.1 Selective Control Valves – Fittings
34.2 Selective Control Valves – Connect Hydraulic Hoses
34.3 Selective Control Valves – Disconnect Hydraulic Hoses
34.4 Selective Control Valves – Connect or Disconnect Hydraulic Hoses at Front Hitch (If Equipped)
34.5 Hydraulic Connections for Implements and Hydraulic Motors
34.6 Connect Implements to Selective Control Valves
34.7 Adjustable Power Beyond Valve
35 Selective Control Valves – Controls
35.1 Selective Control Valves – Set Controls
35.2 Mechanical Selective Control Valves – Controls
35.3 Selective Control Valves, Mechanical – Control Lever
35.4 Selective Control Valves, Mechanical – Transport Lock
35.5 Selective Control Valves, Electronic – Controls
35.6 Selective Control Valves, Electronic – Control Lever
35.7 Selective Control Valves, Electronic – Neutral Position
35.8 Selective Control Valves, Electronic – Extend and Extend Click Position
35.9 Selective Control Valves, Electronic – Retract and Retract Click Position
35.10 Selective Control Valves, Electronic – Float Position (Detent)
36 Selective Control Valves – Settings
36.1 Selective Control Valves, Mechanical – Raise Rate
36.2 Selective Control Valves, Mechanical – Set Feature Mode
36.3 Selective Control Valves, Mechanical – Pressure Settings for Series 450
36.4 Selective Control Valves, Electronic – Menu
36.5 Selective Control Valves, Electronic – Adjust SCV Flow Rate and Flow Time
36.6 Selective Control Valves, Electronic – Loader Mode
36.7 Selective Control Valves, Electronic – Joystick Mode
36.8 Selective Control Valves, Electronic – Advanced Settings
36.9 Operator Presence Sensor – For North America, Australia, and New Zealand Only
37 Front Loader
37.1 Front Loader Mounting Frames for Loaders 620R/623R
37.2 Front Loader Mounting Frames for Loaders 640R/643R, 660R/663R, and 680R/683R
37.3 Front Loader – Hydraulic Quick Release (If Equipped)
37.4 Front Loader?Influence of Engine Speed on Lifting Function
37.5 Mechanical Joystick?Controls
37.6 Electrical Joystick ? Controls
37.7 Electrical Joystick ? Layout and Functions
37.8 Electrical Joystick ? Lock Function (Transport Lock)
38 Wheels and Tires
38.1 Tires and Wheels?Foreword
38.2 General Wheel, Tire, and Tread Guidelines
38.3 Prevent Front Wheel or Fender Contact with Tractor Components
38.4 Change to a Different Tire Size
38.5 Use of Dual Wheels (Easy-to-Attach)
38.6 Service Tires Safely
38.7 Change Wheels Safely
38.8 Wheel Exchange with Wheel Weights
38.9 Tire Combinations – Adjustable Front Axle – 6130M und 6140M
38.10 Tire Combinations – Adjustable Front Axle – 6145M
38.11 Tire Combinations – Front-Wheel Drive Axle – 6130M and 6140M
38.12 Tire Combinations – Front-Wheel Drive Axle – 6145M
38.13 Calculate Tire Combination (Graphic)
38.14 Calculate Tire Combinations, Three-Piece Front Axle
38.15 Tire Labeling? Ascertain the Load Capacity of Tires
38.16 Tire Pressures
38.17 Tire Inflation Pressure Guidelines
38.18 Select Tire Inflation Pressure
39 Front Wheels, Tires, and Tread Widths
39.1 Tires and Wheels?Foreword
39.2 Adjustable Front Axle – Check Toe-In
39.3 Adjustable Front Axle Type B – Adjust Toe-In
39.4 Adjustable Front Axle Type B – Tighten Axle Bolts and Wheels Bolts
39.5 Adjustable Front Axle Type B – Adjust the Wheel Treads
39.6 Adjustable Front Axle Type B – Tread Widths
39.7 Front Tires with Front-Wheel Drive
39.8 Front-Wheel Drive Axle?Toe-In Check and Adjustment
39.9 Front-Wheel Drive Axle?Check Toe-In (Conventional Method)
39.10 Front-Wheel Drive Axle?Check Toe-In Using a Laser Wheel-Measuring Tool
39.11 Front-Wheel Drive Axle?Adjust Toe-In
39.12 Instructions for Front-Wheel Tread Adjustment with Rims for 2, 8, and 16 Positions
39.13 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 2 Positions – 6130M and 6140M
39.14 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 2 Positions – 6145M
39.15 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 8 Positions – 6145M
39.16 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 16 Positions – 6130M and 6140M
39.17 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 16 Positions – 6145M
40 Steering Stop and Fender ? Settings
40.1 Adjust Fenders
40.2 Three-Piece Front Axle (Version 2)?Overview of Axle Category and Axle Type
40.3 Notes on Adjusting the Fenders
40.4 Three-Piece Front Axle (Version 2) ? Notes on Adjusting the Steering Stop – 730, 733 and 735
40.5 Three-Piece Front Axle (Version 2) ? Adjust the Fixed Fenders and Steering Stop – 730, 733 and 735
40.6 Three-Piece Front Axle (Version 2) ? Adjust the Pivoting Fenders and Steering Stop – 730, 733 and 735
40.7 Three-Piece Front Axle (Version 2)?Notes on Adjusting the Steering Stop – 750 and 755
40.8 Three-Piece Front Axle (Version 2)?Adjust the Fixed Fenders and Steering Stop – 750 (M50LD, M50, and M50HD) Part 1
40.9 Three-Piece Front Axle (Version 2)?Adjust the Fixed Fenders and Steering Stop – 750 (M50LD, M50, and M50HD) Part 2
40.10 Three-Piece Front Axle (Version 2)?Adjust the Pivoting Fenders and Steering Stop – 750 (M50LD, M50, and M50HD) Part 1
40.11 Three-Piece Front Axle (Version 2)?Adjust the Pivoting Fenders and Steering Stop – 750 (M50LD, M50, and M50HD) Part 2
41 Rear Wheels, Tires, and Tread Widths
41.1 Tires and Wheels?Foreword
41.2 Instructions for Rear Wheel Tread Adjustment with Rims for 2, 8, and 16 Positions (Flanged Axle)
41.3 Tread Widths for Rear Wheels with Rims for 2 Positions – Flanged Axles, Bolt Circle Diameter 203 mm – 6130M and 6140M
41.4 Tread Widths for Rear Wheels with Rims for 2 Positions – Flanged Axles, Bolt Circle Diameter 275 mm – 6145M
41.5 Tread Widths for Rear Wheels with Rims for 2 Positions (Heavy-Duty Type) – Flanged Axle, Bolt Circle Diameter 275 mm – 6145M
41.6 Tread Widths for Rear Wheels with Rims for 8 Positions – Flanged Axles, Bolt Circle Diameter 275 mm – 6145M
41.7 Tread Widths for Rear Wheels with Rims for 16 Positions – Flanged Axles, Bolt Circle Diameter 203 mm – 6130M and 6140M
41.8 Tread Widths for Rear Wheels with Rims for 16 Positions – Flanged Axles, Bolt Circle Diameter 275 mm – 6145M
41.9 Steel Adjustable Wheels in Combination with Adjustable Rear Axles
41.10 Notes on Rear Wheels – Rack-and-Pinion Axles, Hub Diameter 79 mm
41.11 Rack-and-Pinion Axles, Hub Diameter 79 mm – Adjust Tread Widths
41.12 Tread Widths for Rear Wheels with Rims for 2 Positions – Rack-and-Pinion Axle, Hub Diameter 79 mm – 6130M and 6140M
41.13 Notes on Rear Wheels?Rack-and-Pinion Axles, Hub Diameter 86 mm / 92 mm
41.14 Rack-and-Pinion Axles, Hub Diameter 86 mm / 92 mm?Adjust Tread Widths for Cast Rear Wheels
41.15 Rack-and-Pinion Axles, Hub Diameter 86 mm / 92 mm?Adjust Tread Widths for Steel Rear Wheels (with Adjusting Pinion)
41.16 Rack-and-Pinion Axles, Hub Diameter 86 mm / 92 mm?Adjust Tread Widths for Steel Rear Wheels (without Adjusting Pinion)
41.17 Tread Widths for Rear Wheels with Rims for 2 Positions – Rack-and-Pinion Axle, Hub Diameter 86 mm – 6145M
42 Operator’s Cab
42.1 Avoid Contact with Agricultural Chemicals
42.2 Clean Vehicle of Hazardous Pesticides
42.3 Emergency Exits
42.4 Roll-Over Protective Structure
42.5 Falling Object Protective Structure (FOPS)
42.6 Use the Seat Belt
42.7 Tractors with Cab Suspension
43 Seat Adjustment
43.1 Comfort Seat – MSG85
43.2 Air Comfort Seat (MSG95G)
43.3 Air Comfort Seat (MSG97AL)
43.4 CommandARM??Adjust Height
43.5 Instructional Seat for Training Purposes
44 Steering Column
44.1 Adjust the Steering Wheel
45 Mirrors
45.1 External Mirrors, Manually Adjustable
46 Access Steps
46.1 Access Steps and Handrails
46.2 Remove and Install Left Access Step
46.3 Remove and Install Right Access Step
47 Wiper/Washer System
47.1 Wiper and Washer System
48 Heater/Ventilation/Air Conditioning (HVAC)
48.1 Heater/Ventilation/Air-Conditioning System (HVAC)
49 Lights
49.1 Overview of the Lights
49.2 Shift Lever for Turn Signal and Horn
49.3 Light Switch
49.4 Select Headlights
49.5 Select Worklights
49.6 Worklights of ISOBUS Implement
49.7 Switch On the Hazard Warning Lights
49.8 Beacon Light (Optional)
49.9 Dome Lights
49.10 Access-Step Light
49.11 Seven-Terminal Trailer Socket
50 Power Outlet Sockets
50.1 Socket for GreenStar? Display
50.2 Connection of Memory Storage and Multimedia Appliances
50.3 12-V Power Outlet Socket / Cigarette Lighter
50.4 ISOBUS Socket in Cab
50.5 3-Terminal Power Outlet Socket and Multiple Power Outlet Socket Strip (12 V, SAE)
50.6 3-Terminal Power Outlet Socket (12 V, ECE), Front Hitch
50.7 Signal Socket According to ISO Standard 11786
50.8 Diagnostic Connector (CAN Bus)
50.9 ISOBUS Socket (ISB), Rear Hitch
50.10 Seven-Terminal Trailer Socket, Rear Hitch
50.11 Seven-Terminal Trailer Socket, Front Hitch
51 Accessories
51.1 Storage Tray
51.2 Controls for Hydraulic Quick Release and Worklights on Front Loader (If Equipped)
51.3 Turn Backup Alarm ON and OFF (Optional Equipment)
51.4 Install Additional Monitors
51.5 Open Rear Window and Side Windows
51.6 Rear Window – Cable Guides
51.7 Roof Hatch (If Equipped)
51.8 Pull-Down Sunshade
51.9 Lockable Tank Filler Cap
52 Performance Ballast
52.1 Ballasting Information and Guidelines for Tractors with Single Tires
52.2 General Guidelines for Tractor Weight Based on Engine Horsepower (according to EC Directive 97/68, using PS as Unit of Measurement)
52.3 Selection of Weights
52.4 Load on Rear Wheels
52.5 Measure Rear Wheel Slip
52.6 Fill Tires with Water
52.7 Drain Tires
52.8 Rear Wheel Ballast Weights (Standard Version)
52.9 Change Wheel Weights Safely (Type A)
52.10 Change Wheel Weights Safely (Type B)
52.11 Weight in Three-Point Hitch
52.12 Attach Pickup Weight to the Front Hitch
52.13 Attach the Pickup Weight to the Rear Hitch
52.14 Attach Pickup Weight to the Basic Weight
52.15 Install Front Weights
53 Transport
53.1 Transporting Tractor
53.2 Lashing the Tractor on a Transport Trailers
53.3 Wash Machine After Unloading
53.4 Driving on Public Roads
53.5 Towing Loads and Transporting with Ballast
53.6 Freeing a Mired Machine
53.7 Tow the Tractor
53.8 CommandQuad? PLUS ? Towing the Tractor
53.9 AutoPowr?/IVT??Towing the Tractor
53.10 AutoPowr?/IVT??Release the Park Lock Manually
54 Fuel, Lubricants, and Coolant
54.1 Oilscan? and CoolScan?
55 Diesel Fuel
55.1 Diesel Fuel
55.2 Handling and Storing Diesel Fuel
55.3 Lubricity of Diesel Fuel
55.4 Testing Diesel Fuel
55.5 Biodiesel Fuel
55.6 Minimizing the Effect of Cold Weather on Diesel Engines
55.7 Supplemental Diesel Fuel Additives
56 Diesel Exhaust Fluid
56.1 Diesel Exhaust Fluid (DEF) ? Use in Selective Catalytic Reduction (SCR) Equipped Engines
56.2 Refilling Diesel Exhaust Fluid (DEF) Tank
56.3 Storing Diesel Exhaust Fluid (DEF)
56.4 Testing Diesel Exhaust Fluid (DEF)
56.5 Disposal of Diesel Exhaust Fluid (DEF)
57 Engine Oil – Only for 4-Cylinder Final Tier 4 Engines
57.1 John Deere Break-In Plus? Engine Oil ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
57.2 Diesel Engine Oil ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
57.3 Engine Oil and Filter Service Intervals ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V Engines
58 Engine Coolant
58.1 Diesel Engine Coolant (engine with wet sleeve cylinder liners)
58.2 Operating in Warm Temperature Climates
58.3 John Deere COOL-GARD? II Coolant Extender
58.4 Water Quality for Mixing with Coolant Concentrate
58.5 Testing Coolant Freeze Point
59 Other Lubricants
59.1 Transmission and Hydraulic Oil
59.2 Oil for Front-Wheel Drive Axle
59.3 Multipurpose Extreme Pressure (EP) Grease
59.4 Grease for Automated Lubrication Systems
59.5 Grease
59.6 Multipurpose Grease
59.7 Mixing of Lubricants
59.8 Lubricant Storage
59.9 Alternative and Synthetic Lubricants
60 Service ? General Information
60.1 Required Emission-Related Information
60.2 Safe Maintenance and Cleaning
60.3 Using High-Pressure Washers
60.4 Observe Service Intervals
60.5 Maintenance Intervals
60.6 Maintenance Menu
60.7 Raise the Hood
60.8 Open Service Doors
60.9 Bleed Air from Fuel System – 4-Cylinder Engines
60.10 Jack Up the Tractor, Lifting Points
60.11 General Instructions Regarding the Condition of the Tractor
60.12 Inspect/Replace Hydraulic Hoses
60.13 Important Instructions Regarding Alternator
60.14 Note on Wheels and Tires
60.15 Notes on, Before Initial Start-Up and Daily Service
60.16 Note Regarding the Service Interval for Engine Coolant
60.17 Information on Engine Serial Number, Stage, and Aftertreatment
60.18 Instructions for Starting up the Air-Conditioning System
60.19 Unified Inch Bolt and Screw Torque Values
60.20 Metric Bolt and Screw Torque Values
61 Service Intervals ? Only Tractors with 4-Cylinder Final Tier 4 Engines
61.1 Notes
61.2 Service Daily or Every 10 Operating Hours
61.3 Service (As Required, Annually, Every 2 and 3 Years) – Only on Tractors with 4-Cylinder Final Tier 4 Engines
61.4 Periodic Service – Only on Tractors with 4-Cylinder Final Tier 4 Engines
61.5 Information on Engine Oil Change – Only for 4-Cylinder Final Tier 4 Engines
61.6 Engine Oil and Filter Change
61.7 Engine Oil and Filter Change
61.8 Engine Oil and Filter
