Table of Content:
1 Introduction
1.1 Foreword
1.2 Emissions Performance and Tampering
2 Glossary
2.1 Glossary
2.2 Trademarks
3 Safety
3.1 Recognize Safety Information
3.2 Understand Signal Words
3.3 Follow Safety Instructions
3.4 Prepare for Emergencies
3.5 Wear Protective Clothing
3.6 Protect Against Noise
3.7 Handle Fuel Safely?Avoid Fires
3.8 Handle Starting Fluid Safely
3.9 Fire Prevention
3.10 In Case of Fire
3.11 Avoid Static Electricity Risk When Refueling
3.12 Keep ROPS Installed Properly
3.13 Use Foldable ROPS and Seat Belt Properly
3.14 Stay Clear of Rotating Drivelines
3.15 Use Steps and Handholds Correctly
3.16 Read Operator?s Manuals for ISOBUS Controllers
3.17 Use Seat Belt Properly
3.18 Operating the Tractor Safely
3.19 Avoid Backover Accidents
3.20 Limited Use in Forestry Operation
3.21 Operating the Loader Tractor Safely
3.22 Keep Riders Off Machine
3.23 Instructional Seat
3.24 Use Safety Lights and Devices
3.25 Use a Safety Chain
3.26 Transport Towed Equipment at Safe Speeds
3.27 Use Caution on Slopes, Uneven Terrain, and Rough Ground
3.28 Freeing a Mired Machine
3.29 Avoid Contact with Agricultural Chemicals
3.30 Handle Agricultural Chemicals Safely
3.31 Handling Batteries Safely
3.32 Avoid Heating Near Pressurized Fluid Lines
3.33 Remove Paint Before Welding or Heating
3.34 Handle Electronic Components and Brackets Safely
3.35 Practice Safe Maintenance
3.36 Avoid Hot Exhaust
3.37 Clean Exhaust Filter Safely
3.38 Work In Ventilated Area
3.39 Support Machine Properly
3.40 Prevent Machine Runaway
3.41 Park Machine Safely
3.42 Transport Tractor Safely
3.43 Service Cooling System Safely
3.44 Service Accumulator Systems Safely
3.45 Service Tires Safely
3.46 Service Front-Wheel Drive Tractor Safely
3.47 Tightening Wheel Retaining Bolts/Nuts
3.48 Avoid High-Pressure Fluids
3.49 Do Not Open High-Pressure Fuel System
3.50 Store Attachments Safely
3.51 Decommissioning ? Proper Recycling and Disposal of Fluids and Components
4 Safety Signs
4.1 Do Not Modify ROPS
4.2 Operate the Tractor Safely
4.3 Never Carry Riders
4.4 Regular ROPS Position
4.5 Caution When Operating Front Loader (on Tractors with Mechanical Selective Control Valves)
4.6 Tow Trailer Safely (not on Tractors up to 30 km/h)
4.7 Caution When Operating Rear PTO
4.8 Pressure Accumulator (Brake System)
4.9 Electrical Coolant Heater of Engine (If Equipped)
4.10 .
5 Vehicle Overview
5.1 Identification Views
6 Operator’s Manual ? General Information
6.1 Scope of This Manual
6.2 How to Use This Manual
6.3 Comply with Operator’s Manuals of Implement Manufacturers
7 Operate the Engine
7.1 US EPA Qualified Emergency Use ? SCR Derate Override Option
7.2 Important Engine Information
7.3 Engines with Turbocharger
7.4 Engine Protection
7.5 Required Machine Stop Warning
7.6 Check Engine Indicator Lights and Displays
7.7 Start the Engine – PowrQuad? Transmission
7.8 Start the Engine with an Auxiliary Battery
7.9 Starting With a Slave Battery ? On Tractors with Horizontal Exhaust System
7.10 Shutting Off the Engine
7.11 Battery Disconnect System (If Equipped)
7.12 Park the Tractor – PowrQuad? Transmission
7.13 Tow-Starting
7.14 Fill the Fuel Tank
7.15 Fill the DEF Tank
8 Cold Weather Operation
8.1 Cold Start Aids
8.2 Coolant Heater
8.3 Ground Fault Circuit Interrupter (GFCI)
9 Aftertreatment System
9.1 Exhaust Filter Cleaning, General Information
9.2 Required Machine Stop Warning
9.3 Aftertreatment Indicators Overview
9.4 Access the Engine Menu on the Digital Display
9.5 Passive Exhaust Filter Cleaning
9.6 Automatic Exhaust Filter Cleaning
9.7 Exhaust Filter Cleaning with Tractor Parked
9.8 Exhaust Filter, Service Cleaning
9.9 Exhaust Cleaning System, Information for Operator
9.10 DEF (Diesel Exhaust Fluid) Level Gauge
9.11 Selective Catalytic Reduction (SCR) System Overview
10 Operator Controls
10.1 Vehicle Controls with PowrQuad? Transmission
10.2 Key Switch
10.3 Front-Wheel Drive, Control Elements and Indicator Lights
10.4 Differential Lock, Controls and Indicator Lights
10.5 Creeper – Controls
10.6 PTO – Controls
10.7 Rear Hitch – Controls
10.8 Mechanical Selective Control Valves – Controls
10.9 Joystick, Mechanical (Version 2)
11 Instrument Panel
11.1 Instrument Panel and Indicator Lights ? PowrQuad? Transmission
11.2 Level Indicator ? Fuel Tank and DEF Tank
11.3 Coolant Temperature Gauge
11.4 Digital Display – User Interface
11.5 Digital Display – Display Properties (Basic Settings)
11.6 Digital Display – Information Menu
11.7 Digital Display – Area Calculation
11.8 Digital Display – Service Intervals
11.9 Software Update
12 Drivetrain
12.1 Drive Systems – Overview
13 Front-Wheel Drive
13.1 Front-Wheel Drive, Control Elements and Indicator Lights
13.2 Front-Wheel Drive, Manual Engagement and Disengagement
13.3 Front-Wheel Drive, Engage, and Disengage Automatically
14 Differential Lock
14.1 Differential Lock, Controls and Indicator Lights
14.2 Differential Lock, Manual Engaging/Disengaging
15 Brakes
15.1 Hydraulic Service Brakes
15.2 Single-Line Hydraulic Trailer Brake (If Equipped)
15.3 Park the Tractor – PowrQuad? Transmission
16 Transmission ? General Information
16.1 Reduce Fuel Consumption
16.2 Select Correct Ground Speed
16.3 Notes on Changing to a Different Size of Tire
16.4 Engage Creeper Transmission
16.5 Travel Speed Tables and SRI Values
16.6 Ground Speeds, PowrQuad? Transmission for 30 km/h (16/16) – Tires with SRI 700 and 725
16.7 Ground Speeds, PowrQuad? Transmission for 30 km/h (16/16) – Tires with SRI 750 and 800
16.8 Ground Speeds, PowrQuad? Transmission for 30 km/h (16/16) – Tires with SRI 825
16.9 Ground Speeds, PowrQuad? Transmission for 40 km/h (16/16) – Tires with SRI 700 and 800
16.10 Ground Speeds, PowrQuad? Transmission for 40 km/h (16/16) – Tires with SRI 825
16.11 Ground Speeds (ex Factory with Creeper Transmission), PowrQuad? Transmission 40 km/h (24/24) – Tires (SRI 700 and 725)
16.12 Ground Speeds (ex Factory with Creeper Transmission), PowrQuad? Transmission 40 km/h (24/24) – Tires (SRI 750 and 775)
16.13 Ground Speeds (ex Factory with Creeper Transmission), PowrQuad? Transmission 40 km/h (24/24) – Tires (SRI 800 and 825)
16.14 Ground Speeds (ex Factory without Creeper Transmission), PowrQuad? Transmission 40 km/h (24/24) – Tires (SRI 700, 725, 750 and 775)
16.15 Ground Speeds (ex Factory without Creeper Transmission), PowrQuad? Transmission 40 km/h (24/24) – Tires (SRI 800 and 825)
16.16 Ground Speeds, PowrQuad? Transmission for 40 km/h (20/20) – Tires with SRI 825 and 875
16.17 Ground Speeds, PowrQuad? Transmission for 40 km/h (20/20) – Tires with SRI 925
17 PowrQuad? Transmission
17.1 Shift the PowrQuad? Transmission
17.2 PowrQuad? Transmission – Park the Tractor
18 PTO Shaft, Hitches, and Trailer Hitches
18.1 Hitch – Maximum Lifting Force
19 PTO Shaft – General Information
19.1 Rear PTO – PTO Shield
19.2 Operating Instructions
19.3 PTO Speeds
19.4 PTO Options
20 Rear PTO
20.1 Engage and Disengage the Rear PTO
20.2 Rear PTO – Select Standard Speed (Shiftable PTO)
20.3 Rear PTO – PTO Automatic Shutoff Function (if Equipped)
20.4 Rear PTO – Change the PTO Stub Shaft
20.5 Rear PTO – Connect an Implement
21 Rear Hitches
21.1 Rear Hitch – Operation
21.2 Rear Hitch – Set the Depth Control Stop
21.3 Rear Hitch – Driving under Load with Mounted Implement
21.4 Rear Hitch – Hitch Dampening
21.5 Rear Hitch – Raise Height Limit
21.6 Rear Hitch – Adjust the Rate of Drop
21.7 Rear Hitch – Adjust the Raise Rate
21.8 Rear Hitch – Draft/Depth Control Adjustment
21.9 Rear Hitch – Use Draft Control
21.10 Rear Hitch – Float Position
21.11 Rear Hitch – Remote Control
21.12 Rear Hitch – Direct Actuation
21.13 Three-Point Hitch
21.14 Flat Steel Draft Links
21.15 Telescopic Draft Links
21.16 Quick-Coupling (Hook-Type) Draft Links
21.17 Attach Three-Point Hitch Mounted and Drawn Implements
21.18 Level the Implement
21.19 Center Link
21.20 Center Link Positions
21.21 Hook-Type Center Link
21.22 Adjust Lift Links
21.23 Lift Links – Adjust for Vertical Float
21.24 Sway Blocks, Category 2 (if Equipped)
21.25 Sway Blocks, Category III/IIIN (if Equipped)
21.26 Stabilizer Bar (If Equipped)
21.27 Stabilizing System (If Equipped)
21.28 Draft Links?Adjust Spreading Dimension
22 Trailer Hitches
22.1 Trailer Hitches?Foreword
22.2 CAT II Drawbar
22.3 Proper Use of Drawbar
22.4 Lock the Hitch Pins
22.5 Lock the Height-Adjustable Trailer Hitch
22.6 Latch for Telescopic Draft Links
22.7 Hitch Jaw
22.8 Trailer Hitch with Piton-Fix or Ball-Type (Rigid)
22.9 Height-Adjustable Ball-Type Hitch (Version 1)
22.10 Height-Adjustable Ball-Type Hitch (Version 2)
22.11 Height-Adjustable Trailer Hitch
23 Hydraulic System
23.1 Selective Control Valves – Maximum Permissible Oil Withdrawal (6110M to 6145M)
23.2 Selective Control Valves – Maximum Permissible Oil Withdrawal (6155M)
23.3 Selective Control Valves – Oil Withdrawal with Hydrostatic Drive (with PC Hydraulic System)
23.4 Selective Control Valves – Oil Withdrawal with Hydrostatic Drive (with PFC Hydraulic System)
23.5 Using Large-Volume Hydraulic Cylinders
24 Hydraulic Connections
24.1 Selective Control Valves – Fittings
24.2 Selective Control Valves (SCV) – Connect Hydraulic Hoses
24.3 Selective Control Valves (SCV) – Disconnect Hydraulic Hoses
24.4 Hydraulic Connections for Implements and Hydraulic Motors
24.5 Connect Implements to Selective Control Valves
24.6 Adjustable Power Beyond Valve
25 Selective Control Valves (SCV) ? Controls
25.1 Selective Control Valves (SCVs), Set Controls
25.2 Mechanical Selective Control Valves (SCV) – Controls
25.3 Selective Control Valves (SCV), Mechanical – Control Lever
25.4 Selective Control Valves (SCV), Mechanical – Transport Lock
26 Selective Control Valves (SCV) ? Settings
26.1 Selective Control Valves, Mechanical – Raise Rate
26.2 Selective Control Valves, Mechanical – Set Feature Mode
26.3 Selective Control Valves, Mechanical – Pressure Settings for Series 450
26.4 Operator Presence Sensor – For North America, Australia, and New Zealand Only
27 Front Loader
27.1 Front Loader Mounting Frames for Loaders 620R/623R
27.2 Front Loader Mounting Frames for Loaders 640R/643R, 660R/663R, and 680R/683R
27.3 Front Loader?Influence of Engine Speed on Lifting Function
27.4 Mechanical Joystick?Controls
27.5 Joystick, Mechanical (Version 2)
28 Wheels and Tires
28.1 Tires and Wheels?Foreword
28.2 General Wheel, Tire, and Tread Guidelines
28.3 Prevent Front Wheel or Fender Contact with Tractor Components
28.4 Change to a Different Tire Size
28.5 Use of Dual Wheels (Easy-to-Attach)
28.6 Service Tires Safely
28.7 Change Wheels Safely
28.8 Wheel Exchange with Wheel Weights
28.9 Tire Combinations ? Adjustable Front Axis – 6110M to 6130M
28.10 Tire Combinations ? Adjustable Front Axle – 6145M und 6155M
28.11 Tire Combinations – Front-Wheel Drive Axle – 6110M and 6120M
28.12 Tire Combinations – Front-Wheel Drive Axle – 6130M
28.13 Tire Combinations – Front-Wheel Drive Axle – 6145M
28.14 Tire Combinations – Front-Wheel Drive Axle – 6155M
28.15 Calculate Tire Combination (Graphic)
28.16 Calculate Tire Combination – 6110M to 6145M
28.17 Calculate Tire Combination – 6155M
28.18 Tire Labeling? Ascertain the Load Capacity of Tires
28.19 Tire Pressures
28.20 Tire Inflation Pressure Guidelines
28.21 Select Tire Inflation Pressure
29 Front Wheels, Tires, and Tread Widths
29.1 Tires and Wheels – Foreword
29.2 Adjustable Front Axle – Check Toe-In
29.3 Adjustable Front Axle Type B – Adjust Toe-In
29.4 Adjustable Front Axle Type B – Tighten Axle Bolts and Wheels Bolts
29.5 Adjustable Front Axle Type B – Adjust the Wheel Treads
29.6 Adjustable Front Axle Type B – Tread Widths
29.7 Front Tires with Front-Wheel Drive
29.8 Front-Wheel Drive Axle?Toe-In Check and Adjustment
29.9 Front-Wheel Drive Axle?Check Toe-In (Conventional Method)
29.10 Front-Wheel Drive Axle?Check Toe-In Using a Laser Wheel-Measuring Tool
29.11 Front-Wheel Drive Axle?Adjust Toe-In
29.12 Instructions for Front Wheel Tread Adjustment with Rims for 2, 8, and 16 Positions
29.13 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 2 Positions – 6110M
29.14 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 2 Positions – 6120M
29.15 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 2 Positions – 6130M
29.16 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 2 Positions – 6145M
29.17 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 2 Positions – 6155M
29.18 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 8 Positions – 6145M
29.19 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 8 Positions – 6155M
29.20 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 16 Positions – 6110M
29.21 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 16 Positions – 6120M
29.22 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 16 Positions – 6130M
29.23 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 16 Positions – 6145M
29.24 Three-Piece Front Axle (Version 2) ? Tread Widths for Front Wheels with Rims for 16 Positions – 6155M
30 Steering Stop and Fender ? Settings
30.1 Adjust Fenders
30.2 Three-Piece Front Axle (Version 2)?Overview of Axle Category and Axle Type
30.3 Notes on Adjusting the Fenders
30.4 Three-Piece Front Axle (Version 2) ? Notes on Adjusting the Steering Stop – 730, 733 and 735
30.5 Three-Piece Front Axle (Version 2) ? Adjust the Fixed Fenders and Steering Stop – 730, 733 and 735
30.6 Three-Piece Front Axle (Version 2) ? Adjust the Pivoting Fenders and Steering Stop – 730, 733 and 735
30.7 Three-Piece Front Axle (Version 2)?Notes on Adjusting the Steering Stop – 750 and 755
30.8 Three-Piece Front Axle (Version 2)?Adjust the Fixed Fenders and Steering Stop – 750 (M50LD, M50, and M50HD) Part 1
30.9 Three-Piece Front Axle (Version 2)?Adjust the Fixed Fenders and Steering Stop – 750 (M50LD, M50, and M50HD) Part 2
30.10 Three-Piece Front Axle (Version 2)?Adjust the Pivoting Fenders and Steering Stop – 750 (M50LD, M50, and M50HD) Part 1
30.11 Three-Piece Front Axle (Version 2)?Adjust the Pivoting Fenders and Steering Stop – 750 (M50LD, M50, and M50HD) Part 2
31 Rear Wheels, Tires, and Tread Widths
31.1 Tires and Wheels – Foreword
31.2 Instructions for Rear Wheel Tread Adjustment with Rims for 2, 8 and 16 Positions – Flanged Axle
31.3 Tread Widths for Rear Wheels with Rims for 2 Positions – Flanged Axle (6110M)
31.4 Tread Widths for Rear Wheels with Rims for 2 Positions – Flanged Axle (6120M)
31.5 Tread Widths for Rear Wheels with Rims for 2 Positions – Flanged Axle (6130M)
31.6 Tread Widths for Rear Wheels with Rims for 2 Positions – Flanged Axle (6145M)
31.7 Tread Widths for Rear Wheels with Rims for 2 Positions – Flanged Axle (6155M)
31.8 Tread Widths for Rear Wheels with Rims for 2 Positions (Heavy-Duty Type) – Flanged Axle (6145M)
31.9 Tread Widths for Rear Wheels with Rims for 2 Positions (Heavy-Duty Type) – Flanged Axle (6155M)
31.10 Tread Widths for Rear Wheels with Rims for 8 Positions – Flanged Axle (6145M)
31.11 Tread Widths for Rear Wheels with Rims for 8 Positions – Flanged Axle (6155M)
31.12 Tread Widths for Rear Wheels with Rims for 16 Positions – Flanged Axle (6110M)
31.13 Tread Widths for Rear Wheels with Rims for 16 Positions – Flanged Axle (6120M)
31.14 Tread Widths for Rear Wheels with Rims for 16 Positions – Flanged Axle (6130M)
31.15 Tread Widths for Rear Wheels with Rims for 16 Positions – Flanged Axle (6145M)
31.16 Tread Widths for Rear Wheels with Rims for 16 Positions – Flanged Axle (6155M)
31.17 Steel Adjustable Wheels in Combination with Adjustable Rear Axles
31.18 Notes on Rear Wheels – Rack-and-Pinion Axles, Hub Diameter 79 mm
31.19 Rack-and-Pinion Axles, Hub Diameter 79 mm – Adjust Tread Widths
31.20 Tread Widths for Rear Wheels with Rims for 2 Positions – Rack-and-Pinion Axle, Hub Diameter 79 mm (6110M)
31.21 Tread Widths for Rear Wheels with Rims for 2 Positions – Rack-and-Pinion Axle, Hub Diameter 79 mm (6120M)
31.22 Tread Widths for Rear Wheels with Rims for 2 Positions – Rack-and-Pinion Axle, Hub Diameter 79 mm (6130M)
31.23 Tread Widths on Rear Wheels with Track Adjustment Wheel – Rack-and-Pinion Axle, Hub Diameter 79 mm (6110M)
31.24 Tread Widths on Rear Wheels with Track Adjustment Wheel – Rack-and-Pinion Axle, Hub Diameter 79 mm (6120M)
31.25 Tread Widths on Rear Wheels with Track Adjustment Wheel – Rack-and-Pinion Axle, Hub Diameter 79 mm (6130M)
31.26 Notes on Rear Wheels?Rack-and-Pinion Axles, Hub Diameter 86 mm / 92 mm
31.27 Rack-and-Pinion Axles, Hub Diameter 86 mm / 92 mm?Adjust Tread Widths for Cast Rear Wheels
31.28 Rack-and-Pinion Axles, Hub Diameter 86 mm / 92 mm?Adjust Tread Widths for Steel Rear Wheels (with Adjusting Pinion)
31.29 Rack-and-Pinion Axles, Hub Diameter 86 mm / 92 mm?Adjust Tread Widths for Steel Rear Wheels (without Adjusting Pinion)
31.30 Tread Widths for Rear Wheels with Rims for 2 Positions – Rack-and-Pinion Axle, Hub Diameter 86 mm (6145M)
31.31 Tread Widths for Rear Wheels with Rims for 2 Positions – Rack-and-Pinion Axle, Hub Diameter 86 mm (6155M)
32 Operator’s Station
32.1 Avoid Contact with Agricultural Chemicals
32.2 Clean Vehicle of Hazardous Pesticides
32.3 Fold Down Roll-Over Protective Structure (ROPS)
32.4 Seat Belt Usage
33 Adjusting Seat
33.1 Comfort Seat MSG83
34 Steering Column
34.1 Steering wheel, adjusting
35 Mirrors
35.1 External Mirrors, Manually Adjustable
36 Access steps
36.1 Access Steps and Handrails
36.2 Removal and Installation of Left Access Step
36.3 Removal and Installation of Right Access Step
37 Lights
37.1 Overview of the Lights
37.2 Switch for Turn-Signal Lights and Horn
37.3 Light Switches
37.4 Switch Worklights On and Off
37.5 Switch on Hazard Warning Lights
37.6 Seven-Terminal Trailer Socket
38 Power Sockets
38.1 3-Terminal Power Outlet Socket (12V, SAE)
38.2 Diagnostic Connector (CAN Bus)
38.3 Seven-Terminal Trailer Socket, Rear Hitch
39 Accessories
39.1 Reverse Travel Alarm (Optional Equipment)
40 Performance Ballasting
40.1 Ballasting Information and Guidelines for Tractors with Single Tires
40.2 General Guidelines for Tractor Weight Based on Engine Horsepower (according to EC Directive 97/68, using PS as Unit of Measurement)
40.3 Selection of Weights
40.4 Load on Rear Wheels
40.5 Measure Rear Wheel Slip
40.6 Fill Tires with Water
40.7 Drain Tires
40.8 Rear Wheel Ballast Weights (Standard Version)
40.9 Change Wheel Weights Safely (Type A)
40.10 Change Wheel Weights Safely (Type B)
40.11 Weight in Three-Point Hitch
40.12 Attach the Pickup Weight to the Rear Hitch
40.13 Attach Pickup Weight to the Basic Weight
40.14 Install Front Weights
41 Transport
41.1 Transporting Tractor
41.2 Lashing the Tractor on a Transport Trailers
41.3 Wash Machine After Unloading
41.4 Driving on Public Roads
41.5 Towing Loads and Transporting with Ballast
41.6 Use Safety Chain
41.7 Freeing a Mired Machine
41.8 Tow the Tractor
42 Fuel, Lubricants, and Coolant
42.1 Oilscan? and CoolScan?
43 Diesel Fuel
43.1 Diesel Fuel
43.2 Handling and Storing Diesel Fuel
43.3 Lubricity of Diesel Fuel
43.4 Testing Diesel Fuel
43.5 Biodiesel Fuel
43.6 Minimizing the Effect of Cold Weather on Diesel Engines
43.7 Supplemental Diesel Fuel Additives
44 Diesel Exhaust Fluid
44.1 Diesel Exhaust Fluid (DEF) ? Use in Selective Catalytic Reduction (SCR) Equipped Engines
44.2 Refilling Diesel Exhaust Fluid (DEF) Tank
44.3 Storing Diesel Exhaust Fluid (DEF)
44.4 Testing Diesel Exhaust Fluid (DEF)
44.5 Disposal of Diesel Exhaust Fluid (DEF)
45 Engine Oil – Only for 4-Cylinder Final Tier 4 Engines
45.1 John Deere Break-In Plus? Engine Oil ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
45.2 Diesel Engine Oil ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
45.3 Engine Oil and Filter Service Intervals ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V Engines
46 Engine Oil – Only for 6-Cylinder Final Tier 4 Engines
46.1 John Deere Break-In Plus? Engine Oil ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
46.2 Diesel Engine Oil ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
46.3 Engine Oil and Filter Service Intervals ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V Engines
47 Engine Coolant
47.1 Diesel Engine Coolant (engine with wet sleeve cylinder liners)
47.2 Operating in Warm Temperature Climates
47.3 John Deere COOL-GARD? II Coolant Extender
47.4 Water Quality for Mixing with Coolant Concentrate
47.5 Testing Coolant Freeze Point
48 Other Lubricants
48.1 Transmission and Hydraulic Oil
48.2 Oil for Front-Wheel Drive Axle
48.3 Multipurpose Extreme Pressure (EP) Grease
48.4 Grease for Automated Lubrication Systems
48.5 Grease
48.6 Multipurpose Grease
48.7 Mixing of Lubricants
48.8 Lubricant Storage
48.9 Alternative and Synthetic Lubricants
49 Service ? General Information
49.1 Required Emission-Related Information
49.2 Safe Maintenance and Cleaning
49.3 Using High-Pressure Washers
49.4 Observe Service Intervals
49.5 Maintenance Intervals
49.6 Raise the Hood
49.7 Open Service Doors
49.8 Bleed Air from Fuel System – 4-Cylinder Engines
49.9 Bleed Air from Fuel System – 6-Cylinder Engines
49.10 Jack Up the Tractor – Lifting Points
49.11 General Instructions Regarding the Condition of the Tractor
49.12 Inspect/Replace Hydraulic Hoses
49.13 Important Instructions Regarding Alternator
49.14 Note on Wheels and Tires
49.15 Notes on, Before Initial Start-Up and Daily Service
49.16 Note Regarding the Service Interval for Engine Coolant
49.17 Information on Engine Serial Number, Stage, and Aftertreatment
49.18 Unified Inch Bolt and Screw Torque Values
49.19 Metric Bolt and Screw Torque Values
50 Service Intervals ? Only Tractors with 4-Cylinder Final Tier 4 Engines
50.1 Notes
50.2 Service Daily or Every 10 Operating Hours
50.3 Service (As Required, Annually, Every 2 and 3 Years) – Only on Tractors with 4-Cylinder Final Tier 4 Engines
50.4 Periodic Service – Only on Tractors with 4-Cylinder Final Tier 4 Engines
50.5 Information on Engine Oil Change – Only for 4-Cylinder Final Tier 4 Engines
50.6 Engine Oil and Filter Change
50.7 Engine Oil and Filter Change
50.8 Engine Oil and Filter Change
50.9 Engine Oil and Filter Change
50.10 Service the Engine Air Cleaner
50.11 Service the Engine Air Cleaner
50.12 Service the Cooling System
50.13 Service the Cooling System
50.14 Service the DEF System
50.15 Service the DEF System
50.16 Yearly
50.17 Yearly
50.18 Service after 100 Operating Hours
50.19 Service after 500 Operating Hours
50.20 Service after 1000 Operating Hours
50.21 Service after 1500 Operating Hours
50.22 Service after 2000 Operating Hours
50.23 Service after 2500 Operating Hours
50.24 Service after 3000 Operating Hours
50.25 Service after 3500 Operating Hours
50.26 Service after 4000 Operating Hours
50.27 Service after 4500 Operating Hours
50.28 Service after 5000 Operating Hours
50.29 Service after 5500 Operating Hours
50.30 Service after 6000 Operating Hours
50.31 Service after 6500 Operating Hours
50.32 Service after 7000 Operating Hours
50.33 Service after 7500 Operating Hours
50.34 Service after 8000 Operating Hours
50.35 Service after 8500 Operating Hours
50.36 Service after 9000 Operating Hours
50.37 Service after 9500 Operating Hours
50.38 Service after 10000 Operating Hours
50.39 Information about Further Services
50.40 Record for Further Services
51 Service Intervals ? Only Tractors with 6-Cylinder Final Tier 4 Engines
51.1 Notes
51.2 Service Daily or Every 10 Operating Hours
51.3 Service (As Required, Annually, Every 2 and 3 Years) – Only for 6-Cylinder Final Tier 4 Engines
51.4 Periodic Service (Only for 6-Cylinder Final Tier 4 Engines)
51.5 Information on Engine Oil Change (Only for 6-Cylinder Final Tier 4 Engines)
51.6 Engine Oil and Filter Change
51.7 Engine Oil and Filter Change
51.8 Engine Oil and Filter Change
51.9 Engine Oil and Filter Change
51.10 Service the Engine Air Cleaner
51.11 Service the Engine Air Cleaner
51.12 Service the Cooling System
51.13 Service the Cooling System
51.14 Service the DEF System
51.15 Service the DEF System
51.16 Yearly
51.17 Yearly
51.18 Service after 100 Operating Hours
51.19 Service after 750 Operating Hours
51.20 Service after 1500 Operating Hours
51.21 Service after 2250 Operating Hours
51.22 Service after 3000 Operating Hours
51.23 Service after 3750 Operating Hours
51.24 Service after 4500 Operating Hours
51.25 Service after 5250 Operating Hours
51.26 Service after 6000 Operating Hours
51.27 Service after 6750 Operating Hours
51.28 Service after 7500 Operating Hours
51.29 Service after 8250 Operating Hours
51.30 Service after 9000 Operating Hours
51.31 Service after 9750 Operating Hours
51.32 Service after 10000 Operating Hours
51.33 Information about Further Services
51.34 Record for Further Services
52 Service ? Cleaning
52.1 Clean Radiator, Viscous Fan, Condenser, and Engine Environment
52.2 Check the Fuel Filters – 4-Cylinder Engines
52.3 Check the Fuel Filters – 6-Cylinder Engines
52.4 Service Fuel Tank
52.5 Clean Screen on Filler Neck of DEF Tank,
52.6 DEF Tank Vent – Check Filter
52.7 Cleaning Diesel Exhaust Fluid (DEF) Tank
53 Service ? Electrical System
53.1 Battery ? Disconnect the Electrical Circuit
53.2 Battery ? Disconnect Electrical Circuit – On Tractors with Horizontal Exhaust System
53.3 Fuse and Relay of Electrical Starting Aid – Only on Tractors with Aftertreatment (Final Tier 4)
53.4 Fuse and Relay of Electrical Starting Aid – Only on Tractors with Aftertreatment (Final Tier 4 / Stage IV)
53.5 Fuses and Relays under the Right Access Step
53.6 Fuses and Relays under the Horizontal Exhaust System
53.7 Fuses and Relays (LCS) and (FRM), General Information – Tractors with Open Operator’s Station
53.8 Fuses and Relays (LCS) and (FRM) – Tractors with Open Operator’s Station
53.9 Check Engine Ground Connection – 4-Cylinder Engines
53.10 Check Engine Ground Connection – 6-Cylinder Engines
53.11 Starter Motor
53.12 PTO Actuation – Check Safety Device
53.13 Check the Movement Inhibitor ? PowrQuad? Transmission
53.14 Light Test
53.15 Handling Halogen Bulbs Safely
53.16 Safe Maintenance and Cleaning
53.17 Headlight in the Engine Hood, Low-Beam Headlight – Replace Bulb
53.18 Headlight in the Engine Hood, High-Beam Headlight – Replace Bulb
53.19 Worklight in the Engine Hood – Replace Bulb
53.20 Worklights (Round) – Replace Bulbs
53.21 Worklights (Oval) – Replace Bulbs
53.22 Turn Signal and Clearance Lights – Exchange Lamps
53.23 Tail and Brake Light/Turn-Signal on Fender – Replace Bulb
53.24 License Plate Light – Replace Bulb
53.25 Replace Bulb on Beacon Light
54 Service ? Check Hardware Torques
54.1 Tighten Axle Bolts – Adjustable Front Axle, Type B
54.2 Tighten Wheel Bolts of the Front Wheels, on Vehicles with Adjustable Front Axle Type B
54.3 Tighten Front-Wheel Bolts, on Vehicles with Front-Wheel Drive Axles with 8-Bolt Circle
54.4 Tighten Front-Wheel Bolts of Vehicles with Front-Wheel Drive Axles with 10-Bolt Circle
54.5 Tighten Wheel Bolts of the Rear Wheels, with Flanged Axles
54.6 Tighten Wheel Bolts of the Tear Wheels – Rack-and-Pinion Axles, Hub Diameter 79 mm
54.7 Tighten Wheel Bolts of the Tear Wheels (Rack-and-Pinion Axles, Hub Diameter 86 mm/92 mm)
54.8 Tighten Screws of Wheel Weights
54.9 Front Loader Mounting Frame (Maintenance)
54.10 Tighten Screws of CAT II Drawbar
54.11 Tighten Screws of Trailer Hitch?Guide Rails
54.12 Tighten Screws of Ball-Type Hitch with Attached Arms for Forced Steering
55 Service ? Check
55.1 Check Engine Oil Level – 4-Cylinder Engines
55.2 Check Engine Oil Level (6-Cylinder Engines)
55.3 Engine – Check Drive Belt for Wear
55.4 Check Viscous Fan of Cooling System
55.5 Check Coolant Level
55.6 Use Coolant Test Strips to Check Engine Coolant
55.7 Check Air Intake Hoses
55.8 Front-Wheel Drive Axle (730, 733 and 735) – Axle Housing, Check Oil Level
55.9 Front-Wheel Drive Axle (730, 733 and 735) – Final Drives without Brakes, Check Oil Level
55.10 Check Oil Level of Axle Housing on Front-Wheel Drive Axle (750 and 755)
55.11 Check Oil Level of Final Drives without Brakes on Front-Wheel Drive Axle (750 and 755)
55.12 Transmission/Hydraulic System – Check Oil Level (6110M to 6145M)
55.13 Transmission/Hydraulic System – Check Oil Level (6155M)
55.14 Leak-Off Oil Container (If Equipped)
55.15 Inspect Hydraulic Hoses
55.16 Inspect Seat Belt
55.17 Check Brakes
55.18 Bleed and Check the Brake System
55.19 Check the Manually Operated Hitch for Wear
55.20 Check CUNA Trailer Hitch (Manually Operated) for Wear
55.21 Check Trailer Hitch (Remotely Operated) for Wear
55.22 Trailer Hitch, Check the Guide Rails
55.23 Check Piton-Fix Trailer Hitch for Wear
55.24 Check Ball-Type Hitch for Wear
55.25 Check Drawbar for Wear
56 Service ? Change
56.1 Replace Bulbs
56.2 Replace Engine Oil Filter
56.3 Change Engine Oil – 4-Cylinder Engines
56.4 Change Engine Oil of 6-Cylinder Engines with Aftertreatment
56.5 Engine – Replace Filter of Oil Separator in Crankcase Vent (If Equipped)
56.6 Replace Fuel Filters – 4-Cylinder Engines
56.7 Replace Fuel Filters – 6-Cylinder Engines
56.8 Replace Engine Torsion Damper (6-Cylinder Engines Only)
56.9 Replace the Engine Air Cleaner
56.10 Engine Air Cleaner – Replace Secondary Filter
56.11 Change the Coolant
56.12 Change Diesel Exhaust Fluid (DEF) Dosing Unit Filter
56.13 Installation Position of In-Line DEF Filter
56.14 Change Diesel Exhaust Fluid (DEF) In-Line Filter
56.15 Replace Diesel Particulate Filter (DPF)
56.16 Front-Wheel Drive Axle – Instructions on Changing Oil (Axle Housing and Final Drives)
56.17 Front-Wheel Drive Axle (730, 733 and 735) – Final Drives without Brake, Oil Change
56.18 Front-Wheel Drive Axle (730, 733 and 735) – Axle Housing, Oil Change
56.19 Front-Wheel Drive Axle (750 and 755)?Change Oil of Final Drives without Brake
56.20 Front-Wheel Drive Axle (750 and 755)?Change Oil of Axle Housing (750 and 755) –
56.21 Replace Transmission/Hydraulic Oil Filters
56.22 Change Transmission/Hydraulic Oil and Clean Intake Screen (6110M to 6145M)
56.23 Change Transmission/Hydraulic Oil and Clean Intake Screen (6155M)
57 Service ? Lubrication
57.1 General Information for Lubrication
57.2 Unscheduled Lubrication
57.3 Lubricate Tractor – Lubrication Points
57.4 Lubricate Re
