John Deere 6110m, 6125m, 6130m 6140m, And 6145m (my20- ) Tractors Operator Manuals OMAL229700

Table of Content:

1 Introduction
1.1 Foreword
1.2 Emissions Performance and Tampering
1.3 Download Instructions
2 Glossary
2.1 Glossary
2.2 Trademarks
3 Safety
3.1 Recognize Safety Information
3.2 Understand Signal Words
3.3 Follow Safety Instructions
3.4 Prepare for Emergencies
3.5 Wear Protective Clothing
3.6 Protect Against Noise
3.7 Handle Fuel Safely?Avoid Fires
3.8 Handle Starting Fluid Safely
3.9 Fire Prevention
3.10 In Case of Fire
3.11 Avoid Static Electricity Risk When Refueling
3.12 Keep ROPS Installed Properly
3.13 Use Foldable ROPS and Seat Belt Properly
3.14 Stay Clear of Rotating Drivelines
3.15 Use Steps and Handholds Correctly
3.16 Read Operator?s Manuals for ISOBUS Controllers
3.17 Use Seat Belt Properly
3.18 Operating the Tractor Safely
3.19 Avoid Backover Accidents
3.20 Limited Use in Forestry Operation
3.21 Operating the Loader Tractor Safely
3.22 Keep Riders Off Machine
3.23 Instructional Seat
3.24 Use Safety Lights and Devices
3.25 Transport Towed Equipment at Safe Speeds
3.26 Use Caution on Slopes, Uneven Terrain, and Rough Ground
3.27 Freeing a Mired Machine
3.28 Avoid Contact with Agricultural Chemicals
3.29 Handle Agricultural Chemicals Safely
3.30 Handling Batteries Safely
3.31 Avoid Heating Near Pressurized Fluid Lines
3.32 Remove Paint Before Welding or Heating
3.33 Handle Electronic Components and Brackets Safely
3.34 Practice Safe Maintenance
3.35 Avoid Hot Exhaust
3.36 Clean Exhaust Filter Safely
3.37 Work In Ventilated Area
3.38 Support Machine Properly
3.39 Prevent Machine Runaway
3.40 Park Machine Safely
3.41 Transport Tractor Safely
3.42 Service Cooling System Safely
3.43 Service Accumulator Systems Safely
3.44 Service Tires Safely
3.45 Service Front-Wheel Drive Tractor Safely
3.46 Tightening Wheel Retaining Bolts/Nuts
3.47 Avoid High-Pressure Fluids
3.48 Do Not Open High-Pressure Fuel System
3.49 Store Attachments Safely
3.50 Decommissioning ? Proper Recycling and Disposal of Fluids and Components
4 Safety Signs
4.1 Pictorial Safety Signs
4.2 Operator’s Manual
4.3 Use Seat Belt Properly
4.4 Pickup Hitch
4.5 Pressure Accumulator of the Front Hitch (Tractors without Triple-Link Suspension)
4.6 Pressure Accumulator of the Front Axle Suspension
4.7 Pressure Accumulator of the Front Axle Suspension
4.8 Brake System Pressure Accumulator
4.9 Never Carry Riders (China Only)
4.10 PTOs and Rotating Parts of Implements (China Only)
4.11 Hitch Remote Control (China Only)
4.12 Engine Cooling System (China Only)
4.13 Fuel Tank (China Only)
4.14 .
5 Vehicle Overview
5.1 Identification Views
5.2 Identification Views
6 Operator’s Manual ? General Information
6.1 General Information and Scope of Manual
6.2 How to Use This Manual
6.3 Comply with Operator’s Manuals of Implement Manufacturers
7 Operating the Engine
7.1 EU Qualified Emergency Use ? SCR Derate Override Option
7.2 Important Engine Information
7.3 Engines with Turbocharger
7.4 Engine Protection
7.5 Required Machine Stop Warning
7.6 Engine Menu
7.7 Check Engine Indicator Lights and Displays
7.8 Intelligent Power Management (Power Boost)
7.9 Starting the Engine
7.10 Engine Start with an Auxiliary Battery
7.11 Shutting Off the Engine
7.12 Battery Disconnect System (If Equipped)
7.13 Park the Tractor with PowrQuad?/AutoQuad? PLUS
7.14 Park the Tractor with CommandQuad? PLUS
7.15 Park the Tractor with AutoPowr?/IVT?
7.16 Tow-Starting
7.17 Fill the Fuel Tank
7.18 Fill the DEF Tank
8 Cold-Weather Operation
8.1 Cold Start Aids
8.2 Coolant Heater
8.3 Connecting the Coolant Heater to a 230 V Power Grid
8.4 Ground Fault Circuit Interrupter (GFCI), 120 V
9 Aftertreatment
9.1 Exhaust Filter Cleaning, General Information
9.2 Required Machine Stop Warning
9.3 Aftertreatment Indicators Overview
9.4 Access the Engine Menu
9.5 Exhaust Filter Cleaning Overview
9.6 DEF (Diesel Exhaust Fluid) Level Gauge
9.7 Selective Catalytic Reduction (SCR) System Overview
10 Operator Controls
10.1 Vehicle Controls with PowrQuad? PLUS and AutoQuad? PLUS Transmissions
10.2 Vehicle Controls with CommandQuad? PLUS Transmission without CommandARM?
10.3 Vehicle Controls with CommandQuad? PLUS Transmission with CommandARM?
10.4 Vehicle Controls with AutoPowr? Transmission without CommandARM?
10.5 Vehicle Controls with AutoPowr? Transmission with CommandARM?
10.6 Controls in the Side Console, Overview
10.7 Key Switch
10.8 Come-Home Mode
10.9 Immobilizer
10.10 Secondary Brake System
10.11 Creeper – Controls
10.12 PTO – Controls
10.13 Economy Front Hitch – Controls
10.14 Rear Hitch – Controls
10.15 Mechanical Selective Control Valves – Controls
10.16 Electronic Selective Control Valves – Controls
10.17 Mechanical Joystick (Factory Installed)
10.18 Mechanical Joystick (Retrofitted), R Series Loader for 6M Series Tractors (MY20-)
10.19 Electrical Joystick (Version 1)
10.20 Electrical Joystick (Version 2)
10.21 Front-Wheel Drive – Controls
10.22 Differential Lock – Controls
10.23 iTEC? Basic ? Intelligent Total Equipment Control – Controls
10.24 AutoTrac? – Controls
10.25 ISOBUS Button (ISB)
10.26 Heating, Ventilation and Air-Conditioning System – Controls
10.27 Radio A?Additional Phone Controls
11 Corner Post Display
11.1 Corner Post Display
11.2 Warning Indicators
11.3 Digital Indicators ? Revolution Counter, Ground Speed, Transmission, and Set Speed
11.4 Gauges – Coolant Temperature, DEF Level, and Fuel Level
11.5 Overview of All Menus
11.6 Basic Menu Navigation
11.7 Information Display, Run Pages
11.8 Display Settings, Menu
11.9 Display Settings, Brightness
11.10 Display Settings, Display Modes (Day/Night)
11.11 Display Settings, Language
11.12 Display Settings, Units
11.13 Display Settings, Numeric Format
11.14 Display Settings, Information on the Corner Post Display
11.15 Work Monitor, Menu
11.16 Work Monitor, Counters A and B
11.17 Work Monitor, Readings
11.18 Work Monitor, Implement Width
11.19 Work Monitor, Recording Trigger
11.20 Layout Manager, Settings
11.21 Set up Controls
12 CommandARM? Controls
12.1 CommandARM?, Controls (with CommandQuad? Plus)
12.2 CommandARM?, Controls (with AutoPowr?/IVT?)
13 Radio A?Operation
13.1 Radio A?Controls and Instruments
13.2 Radio A?Additional Phone Controls
13.3 Radio A?Microphone for Bluetooth Applications
13.4 Radio A?Connection of Memory Storage and Multimedia Appliances
13.5 FM, MW, LW and DAB/DAB+-Compliant Radio Antenna (Europe Only)
14 Radio B?Operation
14.1 Radio B?Identification Views and Features
14.2 Radio B?Controls and Instruments
14.3 Radio B?Connection of Memory Storage and Multimedia Appliances
14.4 FM, MW, LW and DAB/DAB+-Compliant Radio Antenna (Europe Only)
15 Guidance
15.1 AutoTrac? Guidance System (If Equipped)
15.2 AutoTrac? Guidance with GreenStar? Display
15.3 AutoTrac? Basic Guidance with Corner Post Display
15.4 Operate Guidance Systems Safely
15.5 Enable AutoTrac? Basic
15.6 Disable AutoTrac? Basic
15.7 AutoTrac? Resume Switch
15.8 Activate AutoTrac? Basic
15.9 Disengage AutoTrac? Basic
15.10 Reactivate AutoTrac? Basic on Next Pass
15.11 AutoTrac? Basic Menu
15.12 AutoTrac? Basic Map
15.13 AutoTrac? Status Pie
15.14 AutoTrac? Basic Track Setup
15.15 AutoTrac? Basic Tread Width
15.16 AutoTrac? Basic Shift Size
15.17 AutoTrac? Basic Vehicle
15.18 AutoTrac? Basic Tuning
15.19 StarFire? Correction Mode
15.20 AutoTrac? Basic TCM Calibration
15.21 StarFire? USB Drive
15.22 StarFire? GPS Status
15.23 AutoTrac? Basic Settings Locked
15.24 AutoTrac? Basic About
15.25 GPS Receiver Offset Values
15.26 AutoTrac? Universal Information
16 Intelligent Total Equipment Control (iTEC?)
16.1 iTEC? Basic, General Information
16.2 Basic Menu Navigation
16.3 iTEC? Basic, Menu
16.4 iTEC? Basic, Access Functions
16.5 iTEC? Basic, Settings
17 Drivetrain
17.1 Drive Systems – Overview
18 Front-Wheel Drive
18.1 Front-Wheel Drive, Control Elements and Indicator Lights
18.2 Front-Wheel Drive, Manual Engagement and Disengagement
18.3 Front-Wheel Drive, Automatic Engagement and Disengagement
18.4 Tractor Equipped With Front Suspension Option
19 Differential Lock
19.1 Differential Lock, Controls and Indicator Lights
19.2 Differential Lock, Manual Engaging/Disengaging
19.3 Differential Lock, Automatic Engaging/Disengaging
20 Brakes
20.1 Hydraulic Service Brakes
20.2 Secondary Brake System
20.3 Single-Line Hydraulic Trailer Brake (If Equipped)
20.4 Dual-Line Hydraulic Trailer Brake* (If Equipped)
20.5 Air Trailer Brake (If Equipped)
20.6 Trailer Brake Test
20.7 Socket for the Anti-Lock Brake System (ABS) of Trailer
20.8 Park the Tractor with PowrQuad?/AutoQuad? PLUS
20.9 Park the Tractor with CommandQuad? PLUS
20.10 Park the Tractor with AutoPowr?/IVT?
20.11 Chock Block
21 Transmission – General Information
21.1 Reduce Fuel Consumption
21.2 Select Correct Ground Speed
21.3 Notes on Changing to a Different Size of Tire
21.4 Engage Creeper Transmission
21.5 Travel Speed Tables and SRI Values
21.6 Ground Speeds, PowrQuad? PLUS Transmission for 30 km/h (16/16) – Tires with SRI 700 and 725
21.7 Ground Speeds, PowrQuad? PLUS Transmission for 30 km/h (16/16) – Tires with SRI 750 and 800
21.8 Ground Speeds, PowrQuad? PLUS Transmission for 30 km/h (16/16) – Tires with SRI 825
21.9 Ground Speeds, PowrQuad? PLUS Transmission for 40 km/h (16/16) – Tires with SRI 700 and 725
21.10 Ground Speeds, PowrQuad? PLUS Transmission for 40 km/h (16/16) – Tires with SRI 750 and 800
21.11 Ground Speeds, PowrQuad? PLUS Transmission for 40 km/h (16/16) – Tires with SRI 825
21.12 Ground Speeds (ex Factory with Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 700 and 725)
21.13 Ground Speeds (ex Factory with Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 750 and 775)
21.14 Ground Speeds (ex Factory with Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 800 and 825)
21.15 Ground Speeds (ex Factory without Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 700, 725, 750 and 775)
21.16 Ground Speeds (ex Factory without Creeper Transmission), PowrQuad? PLUS and AutoQuad? PLUS Transmissions 40 km/h (24/24) – Tires (SRI 800 and 825)
21.17 Travel Speeds, AutoQuad? PLUS Transmission with Eco Shift? for 40 km/h (24/24) – Tires with SRI 700 and 725
21.18 Travel Speeds, AutoQuad? PLUS Transmission with Eco Shift? for 40 km/h (24/24) – Tires with SRI 750 and 775
21.19 Travel Speeds, AutoQuad? PLUS Transmission with Eco Shift? for 40 km/h (24/24) – Tires with SRI 800 and 825
21.20 Travel Speeds, CommandQuad? PLUS Transmission for 40 km/h (24/24) – Tires with SRI 700, 725, 750 and 775
21.21 Ground Speeds, CommandQuad? PLUS Transmission for 40 km/h (24/24) – Tires with SRI 800 and 825
21.22 Travel Speeds, CommandQuad? PLUS Transmission with Eco Shift? for 40 km/h (24/24) – Tires with SRI 700, 725, 750, and 775
21.23 Ground Speeds, CommandQuad? PLUS Transmission with Eco Shift? for 40 km/h (24/24) – Tires with SRI 800 and 825
22 PowrQuad? PLUS Transmission
22.1 PowrQuad? PLUS Transmission, Controls
22.2 PowrQuad? PLUS Transmission, Park Lock
22.3 PowrQuad? PLUS Transmission, Reverse Drive Lever
22.4 PowrQuad? PLUS Transmission, Range-Shift Lever
22.5 PowrQuad? PLUS Transmission, Gearshift Buttons
22.6 PowrQuad? PLUS Transmission, Clutch Pedal and Clutch Button
22.7 PowrQuad? PLUS Transmission, Speed Control Pedal and Hand Throttle
22.8 PowrQuad? PLUS Transmission, Engine Set Speed
22.9 PowrQuad? PLUS Transmission, Cold-Weather Operation
22.10 PowrQuad? PLUS Transmission, Come-Home Mode
22.11 PowrQuad? PLUS Transmission, Menu
22.12 Symbols in the Transmission Menu
22.13 PowrQuad? PLUS Transmission, PowrReverser?
22.14 PowrQuad? PLUS Transmission, Reverse/Forward Ratio
22.15 PowrQuad? PLUS Transmission, Backup Alarm
23 AutoQuad? PLUS Transmission
23.1 AutoQuad? PLUS Transmission, Controls
23.2 AutoQuad? PLUS Transmission, Park Lock
23.3 AutoQuad? PLUS Transmission, Reverse Drive Lever
23.4 AutoQuad? PLUS Transmission, Range-Shift Lever
23.5 AutoQuad? PLUS Transmission, Gearshift Buttons
23.6 AutoQuad? PLUS Transmission, Clutch Pedal and Clutch Button
23.7 AutoQuad? PLUS Transmission, Automatic Gear Shifting
23.8 AutoQuad? PLUS Transmission, Speed Control Pedal and Hand Throttle
23.9 AutoQuad? PLUS Transmission, Engine Set Speed
23.10 AutoQuad? PLUS Transmission, Cold-Weather Operation
23.11 AutoQuad? PLUS Transmission, Come-Home Mode
23.12 AutoQuad? PLUS Transmission, Menu
23.13 Symbols in the Transmission Menu
23.14 AutoQuad? PLUS Transmission, Transmission Mode
23.15 AutoQuad? PLUS Transmission, PowrReverser?
23.16 AutoQuad? PLUS Transmission, Reverse/Forward Ratio
23.17 AutoQuad? PLUS Transmission, Backup Alarm
24 CommandQuad? PLUS Transmission
24.1 CommandQuad? PLUS Transmission, Controls without CommandARM?
24.2 CommandQuad? PLUS Transmission, Controls with CommandARM?
24.3 CommandQuad? PLUS Transmission, Control Lever of the Park Lock
24.4 CommandQuad? PLUS Transmission, Reverse Drive Lever
24.5 CommandQuad? PLUS Transmission, Range Shift Unit
24.6 CommandQuad? PLUS Transmission, Shift Lever
24.7 CommandQuad? PLUS Transmission, Set Maximum Ground Speed
24.8 CommandQuad? PLUS Transmission, Speed Control Pedal and Hand Throttle
24.9 CommandQuad? PLUS Transmission, Engine Set Speed
24.10 CommandQuad? PLUS Transmission, Select Start Gear
24.11 CommandQuad? PLUS Transmission, Brake Pedals and Clutch Pedal (AutoClutch Function)
24.12 CommandQuad? PLUS Transmission, Special Features when Maneuvering the Tractor
24.13 CommandQuad? PLUS Transmission, Adjust Driving Characteristics
24.14 CommandQuad? PLUS Transmission, Operating with Trailer on Hillsides in Slippery Conditions
24.15 CommandQuad? PLUS Transmission, Stopping and Parking the Tractor
24.16 CommandQuad? PLUS Transmission, Come-Home Mode
24.17 CommandQuad? PLUS Transmission, Tow the Tractor
24.18 CommandQuad? PLUS Transmission, Menu
24.19 Symbols in the Transmission Menu
24.20 CommandQuad? PLUS Transmission, Start Gears
24.21 CommandQuad? PLUS Transmission, PowrReverser?
24.22 CommandQuad? PLUS Transmission, Reverse/Forward Ratio
24.23 CommandQuad? PLUS Transmission, Minimum Speed
24.24 CommandQuad? PLUS Transmission, Load Anticipation
24.25 CommandQuad? PLUS Transmission, Droop with PTO OFF/ON
24.26 CommandQuad? PLUS Transmission, AutoClutch
24.27 CommandQuad? PLUS Transmission, Backup Alarm
25 AutoPowr?/IVT? Transmission
25.1 AutoPowr?/IVT? ? Reverse Drive Lever
25.2 AutoPowr?/IVT? ? Speed Control Lever
25.3 AutoPowr?/IVT? ? Stop and Park the Tractor
25.4 AutoPowr?/IVT? ? Speed Control Pedal and Hand Throttle
25.5 AutoPowr?/IVT? ? Engine Set Speed
25.6 AutoPowr?/IVT? ? Travel Set Speed
25.7 AutoPowr?/IVT? ? Travel Set Speed, Guidelines
25.8 AutoPowr?/IVT? ? Clutch Pedal
25.9 AutoPowr?/IVT? ? Special Features when Maneuvering the Tractor
25.10 AutoPowr?/IVT? ? Downhill Braking of Tractors with Trailer
25.11 AutoPowr?/IVT? ? Using Individual Brake Pedals
25.12 AutoPowr?/IVT? ? Cold-Weather Starting
25.13 AutoPowr?/IVT? ? Come-Home Mode
25.14 AutoPowr?/IVT? ? Tow the Tractor
25.15 AutoPowr?/IVT? ? Menu
25.16 AutoPowr?/IVT? ? Symbols in the Transmission Menu
25.17 AutoPowr?/IVT? ? Transmission Mode
25.18 AutoPowr?/IVT? ? PowrReverser?
25.19 AutoPowr?/IVT? ? Reverse/Forward Ratio
25.20 AutoPowr?/IVT? ? Min RPM
25.21 AutoPowr?/IVT? ? Transmission, Load Anticipation
25.22 AutoPowr?/IVT? ? Droop with PTO OFF/ON
25.23 AutoPowr?/IVT? ? AutoClutch
25.24 AutoPowr?/IVT? ? Backup Alarm
26 PTO Shaft, Hitches, and Trailer Hitches
26.1 Hitch – Maximum Lifting Force
27 PTO Shaft – General Information
27.1 Front PTO?PTO Shield
27.2 Rear PTO?PTO Shield
27.3 None-Rotating PTO Guard
27.4 Operating Instructions
27.5 PTO Speeds
27.6 PTO Options
28 Front PTO
28.1 Front PTO
28.2 Engage and Disengage the Front PTO
28.3 Front PTO ? PTO Automatic Shutoff Function
29 Rear PTO
29.1 Rear PTO
29.2 Engage and Disengage the Rear PTO
29.3 Rear PTO – Select Standard Speed (Shiftable PTO)
29.4 Rear PTO – Remote Control and Function
29.5 Rear PTO – PTO Automatic Shutoff Function
29.6 Rear PTO?Change the PTO Stub Shaft
29.7 Rear PTO – Connect an Implement
30 Front Hitch
30.1 Economy Front Hitch – Controls
30.2 Economy Front Hitch
30.3 Front Hitch?Center Link
30.4 Front Hitch?Center Link Positions
30.5 Front Hitch?Hook-Type Center Link
31 Rear Hitch
31.1 Rear Hitch – Menu
31.2 Rear Hitch – Operation without CommandARM?
31.3 Rear Hitch – Operation with CommandARM?
31.4 Rear Hitch – Set the Depth Control Stop
31.5 Rear Hitch – Driving under Load with Mounted Implement
31.6 Rear Hitch – Hitch Dampening
31.7 Rear Hitch – Raise Height Limit
31.8 Rear Hitch – Adjust the Rate of Drop
31.9 Rear Hitch – Adjust the Raise Rate
31.10 Rear Hitch – Draft/Depth Control Adjustment
31.11 Rear Hitch – Use Draft Control
31.12 Rear Hitch – Float Position
31.13 Rear Hitch – Remote Control
31.14 Rear Hitch – Direct Actuation
31.15 Three-Point Hitch
31.16 Flat Steel Draft Links
31.17 Telescopic Draft Links
31.18 Quick-Coupling (Hook-Type) Draft Links
31.19 Attach Three-Point Hitch Mounted and Drawn Implements
31.20 Level the Implement
31.21 Center Link
31.22 Center Link Positions
31.23 Hook-Type Center Link
31.24 Hydraulic Center Link (If Equipped)
31.25 Adjust Lift Links
31.26 Lift Links – Adjust for Vertical Float
31.27 Sway Blocks, Category II (If Equipped)
31.28 Stabilizer Bar (If Equipped)
31.29 Stabilizing System (If Equipped)
31.30 Draft Links?Adjust Spreading Dimension
32 Trailer Hitches
32.1 Trailer Hitches?Foreword
32.2 CAT II Drawbar
32.3 Proper Use of Drawbar
32.4 Lock the Hitch Pins
32.5 Lock the Height-Adjustable Trailer Hitch
32.6 Latch for Telescopic Draft Links
32.7 Hitch Jaw
32.8 Trailer Hitch with Piton-Fix or Ball-Type (Rigid)
32.9 Height-Adjustable Ball-Type Hitch (Version 1)
32.10 Height-Adjustable Ball-Type Hitch (Version 2)
32.11 Height-Adjustable Trailer Hitch
32.12 Remote Control for Trailer Hitch (If Equipped)
32.13 Hydraulic Pickup Hitch (Mechanically Actuated)
32.14 Hydraulic Pickup Hitch (Electrically Actuated)
33 Hydraulic System
33.1 Selective Control Valves – Maximum Permissible Oil Withdrawal
33.2 Selective Control Valves – Oil Withdrawal with Hydrostatic Drive (with PC Hydraulic System)
33.3 Selective Control Valves – Oil Withdrawal with Hydrostatic Drive (with PFC Hydraulic System)
33.4 Using Large-Volume Hydraulic Cylinders
33.5 Additional Oil Reservoir (If Equipped)
34 Hydraulic Connections
34.1 Selective Control Valves – Fittings
34.2 Selective Control Valves – Connect Hydraulic Hoses
34.3 Selective Control Valves – Disconnect Hydraulic Hoses
34.4 Selective Control Valves – Connect or Disconnect Hydraulic Hoses at Front Hitch (If Equipped)
34.5 Hydraulic Connections for Implements and Hydraulic Motors
34.6 Connect Implements to Selective Control Valves
34.7 Adjustable Power Beyond Valve
35 Selective Control Valves (SCVs) – Controls
35.1 Selective Control Valves – Set Controls
35.2 Mechanical Selective Control Valves – Controls
35.3 Selective Control Valves, Mechanical – Control Lever
35.4 Selective Control Valves, Mechanical – Transport Lock
35.5 Selective Control Valves, Electronic – Controls
35.6 Selective Control Valves, Electronic – Control Lever
35.7 Selective Control Valves, Electronic – Neutral Position
35.8 Selective Control Valves, Electronic – Extend and Extend Click Position
35.9 Selective Control Valves, Electronic – Retract and Retract Click Position
35.10 Selective Control Valves, Electronic – Float Position (Detent)
36 Selective Control Valves (SCVs) – Settings
36.1 Selective Control Valves, Mechanical – Raise Rate
36.2 Selective Control Valves, Mechanical – Set Feature Mode
36.3 Selective Control Valves, Mechanical – Pressure Settings for Series 450
36.4 Selective Control Valves, Electronic – Menu
36.5 Selective Control Valves, Electronic – Adjust SCV Flow Rate and Flow Time
36.6 Selective Control Valves, Electronic – Loader Mode
36.7 Selective Control Valves, Electronic – Joystick Mode
36.8 Selective Control Valves, Electronic – Advanced Settings
36.9 Operator Presence Sensor – For North America, Australia, and New Zealand Only
37 Front Loader
37.1 Front Loader Mounting Frames for Loaders 620R/623R
37.2 Front Loader Mounting Frames for Loaders 640R/643R, 660R/663R, and 680R/683R
37.3 Front Loader?Hydraulic Quick Release (If Equipped)
37.4 Front Loader?Influence of Engine Speed on Lifting Function
37.5 Mechanical Joystick (Factory Installed)?Controls
37.6 Mechanical Joystick (Retrofitted), R Series Loader for 6M Series Tractors (MY20-)?Controls
37.7 Electrical Joystick?Identify the Version
37.8 Electrical Joystick (Version 1)?Controls
37.9 Electrical Joystick (Version 1)?Layout and Functions
37.10 Electrical Joystick (Version 1)?Lock Function (Transport Lock)
37.11 Electrical Joystick (Version 2)?Controls
37.12 Electrical Joystick (Version 2)?Hand-Presence Detection System
37.13 Electrical Joystick (Version 2)?Hand-Presence Detection System, Error Message
37.14 Electrical Joystick (Version 2)?Layout and Functions
37.15 Electrical Joystick (Version 2)?Available Presets
37.16 Electrical Joystick (Version 2)?Lock Function (Transport Lock)
38 Wheels and Tires
38.1 Tractor Models and Corresponding Axles?Overview, Tractors 6090M to 6210M (MY20- ) with Cab
38.2 Tires and Wheels?Foreword
38.3 General Wheel, Tire, and Tread Guidelines
38.4 Prevent Front Wheel or Fender Contact with Tractor Components
38.5 Change to a Different Tire Size
38.6 Changing the Tire Combination
38.7 Use of Dual Wheels (Easy-to-Attach)
38.8 Service Tires Safely
38.9 Change Wheels Safely
38.10 Wheel Exchange with Wheel Weights
38.11 Tire Combinations?Adjustable Front Axle (6110M and 6125M, Tier 2)
38.12 Tire Combinations?Adjustable Front Axle (6130M and 6140M)
38.13 Tire Combinations?Adjustable Front Axle (6140M, Tier 2)
38.14 Tire Combinations?Adjustable Front Axle (6145M)
38.15 Tire Combinations?Front-Wheel Drive Axle (6110M and 6125M, Tier 2)
38.16 Tire Combinations?Front-Wheel Drive Axle (6130M and 6140M)
38.17 Tire Combinations?Front-Wheel Drive Axle (6140M, Tier 2)
38.18 Tire Combinations?Front-Wheel Drive Axle (6145M)
38.19 Tire Labeling?Ascertain the Load Capacity of Tires
38.20 Tire Load Index
38.21 Tire Pressures
38.22 Tire Inflation Pressure Guidelines
38.23 Select Tire Inflation Pressure
39 Front Wheels, Tires, and Tread Widths
39.1 Tires and Wheels?Foreword
39.2 Adjustable Front Axle?Check Toe-In
39.3 Adjustable Front Axle Type B?Adjust Toe-In
39.4 Adjustable Front Axle Type B?Tighten Axle Bolts and Wheels Bolts
39.5 Adjustable Front Axle Type B?Adjust the Wheel Treads
39.6 Adjustable Front Axle Type B?Tread Widths
39.7 Front Tires with Front-Wheel Drive
39.8 Front-Wheel Drive Axle?Toe-In Check and Adjustment
39.9 Front-Wheel Drive Axle?Check Toe-In (Conventional Method)
39.10 Front-Wheel Drive Axle?Check Toe-In Using a Laser Wheel-Measuring Tool
39.11 Front-Wheel Drive Axle?Adjust Toe-In
39.12 Instructions for Front-Wheel Tread Adjustment with Rims for 2, 8, and 16 Positions
39.13 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 2 Positions (6110M and 6125M, Tier 2)
39.14 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 2 Positions (6130M and 6140M)
39.15 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 2 Positions (6140M, Tier 2)
39.16 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 2 Positions (6145M)
39.17 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 8 Positions (6140M, Tier 2)
39.18 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 8 Positions (6145M)
39.19 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 16 Positions (6110M and 6125M, Tier 2)
39.20 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 16 Positions (6130M and 6140M)
39.21 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 16 Positions (6140M, Tier 2)
39.22 Three-Piece Front Axle (Version 2)?Tread Widths for Front Wheels with Rims for 16 Positions (6145M)
40 Steering Stop and Fender ? Settings
40.1 Adjust Fenders
40.2 Three-Piece Front Axle (Version 2)?Identify Axle Type
40.3 Notes on Adjusting the Fenders
40.4 Three-Piece Front Axle (Version 2)?Notes on Adjusting the Steering Stop (730, 733, 735, and 736)
40.5 Three-Piece Front Axle (Version 2)?Adjust the Fixed Fenders and Steering Stop (730, 733, 735, and 736)
40.6 Three-Piece Front Axle (Version 2)?Adjust the Pivoting Fenders and Steering Stop (730, 733, 735, and 736)
40.7 Three-Piece Front Axle (Version 2)?Notes on Adjusting the Steering Stop (750 and 755)
40.8 Three-Piece Front Axle (Version 2)?Adjust the Fixed Fenders and Steering Stop (750) Part 1
40.9 Three-Piece Front Axle (Version 2)?Adjust the Fixed Fenders and Steering Stop (750) Part 2
40.10 Three-Piece Front Axle (Version 2)?Adjust the Pivoting Fenders and Steering Stop (750) Part 1
40.11 Three-Piece Front Axle (Version 2)?Adjust the Pivoting Fenders and Steering Stop (750) Part 2
41 Rear Wheels, Tires, and Tread Widths
41.1 Tires and Wheels?Foreword
41.2 Instructions for Rear Wheel Tread Adjustment with Rims for 2, 8, and 16 Positions (Flanged Axle)
41.3 Tread Widths for Rear Wheels with Rims for 2 Positions?Flanged Axles, Bolt Circle Diameter 203 mm (6110M and 6125M, Tier 2)
41.4 Tread Widths for Rear Wheels with Rims for 2 Positions?Flanged Axles, Bolt Circle Diameter 203 mm (6130M and 6140M)
41.5 Tread Widths for Rear Wheels with Rims for 2 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6110M and 6125M, Tier 2)
41.6 Tread Widths for Rear Wheels with Rims for 2 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6130M and 6140M)
41.7 Tread Widths for Rear Wheels with Rims for 2 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6140M, Tier 2)
41.8 Tread Widths for Rear Wheels with Rims for 2 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6145M)
41.9 Tread Widths for Rear Wheels with Rims for 2 Positions, Heavy-Duty Type?Flanged Axles, Bolt Circle Diameter 275 mm (6110M and 6125M, Tier 2)
41.10 Tread Widths for Rear Wheels with Rims for 2 Positions, Heavy-Duty Type?Flanged Axles, Bolt Circle Diameter 275 mm (6130M and 6140M)
41.11 Tread Widths for Rear Wheels with Rims for 2 Positions, Heavy-Duty Type?Flanged Axles, Bolt Circle Diameter 275 mm (6140M, Tier 2)
41.12 Tread Widths for Rear Wheels with Rims for 2 Positions, Heavy-Duty Type?Flanged Axles, Bolt Circle Diameter 275 mm (6145M)
41.13 Tread Widths for Rear Wheels with Rims for 8 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6140M, Tier 2)
41.14 Tread Widths for Rear Wheels with Rims for 8 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6145M)
41.15 Tread Widths for Rear Wheels with Rims for 16 Positions?Flanged Axles, Bolt Circle Diameter 203 mm (6110M and 6125M, Tier 2)
41.16 Tread Widths for Rear Wheels with Rims for 16 Positions?Flanged Axles, Bolt Circle Diameter 203 mm (6130M and 6140M)
41.17 Tread Widths for Rear Wheels with Rims for 16 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6110M and 6125M, Tier 2)
41.18 Tread Widths for Rear Wheels with Rims for 16 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6130M and 6140M)
41.19 Tread Widths for Rear Wheels with Rims for 16 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6140M, Tier 2)
41.20 Tread Widths for Rear Wheels with Rims for 16 Positions?Flanged Axles, Bolt Circle Diameter 275 mm (6145M)
41.21 Steel Adjustable Wheels in Combination with Adjustable Rear Axles
41.22 Notes on Rear Wheels?Rack-and-Pinion Axles, Hub Diameter 79 mm with Single Tapered Clamping Sleeves
41.23 Rack-and-Pinion Axles, Hub Diameter 79 mm with Single Tapered Clamping Sleeves?Adjust Tread Widths
41.24 Tread Widths for Rear Wheels with Rims for 2 Positions?Rack-and-Pinion Axles, Hub Diameter 79 mm (6110M and 6125M, Tier 2)
41.25 Tread Widths for Rear Wheels with Rims for 2 Positions?Rack-and-Pinion Axles, Hub Diameter 79 mm (6130M and 6140M)
41.26 Tread Widths for Rear Wheels with Rims for 2 Positions, Heavy-Duty Type?Rack-and-Pinion Axles, Hub Diameter 79 mm (6110M and 6125M, Tier 2)
41.27 Tread Widths for Rear Wheels with Rims for 2 Positions, Heavy-Duty Type?Rack-and-Pinion Axles, Hub Diameter 79 mm (6130M and 6140M)
41.28 Tread Widths on Rear Wheels with Track Adjustment Wheel?Rack-and-Pinion Axles, Hub Diameter 79 mm (6110M and 6125M, Tier 2)
41.29 Tread Widths on Rear Wheels with Track Adjustment Wheel?Rack-and-Pinion Axles, Hub Diameter 79 mm (6130M and 6140M)
41.30 Notes on Rear Wheels?Rack-and-Pinion Axles, Hub Diameter 86, 92, and 100 mm with Single Tapered Clamping Sleeves
41.31 Rack-and-Pinion Axles, Hub Diameter 86, 92, and 100 mm with Single Tapered Clamping Sleeves?Adjust Tread Widths for Cast Rear Wheels
41.32 Rack-and-Pinion Axles, Hub Diameter 86, 92, and 100 mm with Single Tapered Clamping Sleeves?Adjust Tread Widths for Steel Rear Wheels (with Adjusting Pinion)
41.33 Rack-and-Pinion Axles, Hub Diameter 86, 92, and 100 mm with Single Tapered Clamping Sleeves?Adjust Tread Widths for Steel Rear Wheels (without Adjusting Pinion)
41.34 Tread Widths for Rear Wheels with Rims for 2 Positions?Rack-and-Pinion Axles, Hub Diameter 86 mm (6110M and 6125M, Tier 2)
41.35 Tread Widths for Rear Wheels with Rims for 2 Positions?Rack-and-Pinion Axles, Hub Diameter 86 mm (6130M and 6140M)
41.36 Tread Widths for Rear Wheels with Rims for 2 Positions?Rack-and-Pinion Axles, Hub Diameter 86 mm (6140M, Tier 2)
41.37 Tread Widths for Rear Wheels with Rims for 2 Positions?Rack-and-Pinion Axles, Hub Diameter 86 mm (6145M)
41.38 Tread Widths for Rear Wheels with Rims for 2 Positions, Heavy-Duty Type?Rack-and-Pinion Axles, Hub Diameter 86 mm (6140M, Tier 2)
41.39 Tread Widths for Rear Wheels with Rims for 2 Positions, Heavy-Duty Type?Rack-and-Pinion Axles, Hub Diameter 86 mm (6145M)
42 Operator’s Cab
42.1 Cab Classification According to EN 15695-1 (for Application of Crop Protection Chemicals and Liquid Fertilizer)
42.2 Avoid Contact with Agricultural Chemicals
42.3 Clean Vehicle of Hazardous Pesticides
42.4 Emergency Exits
42.5 Roll-Over Protective Structure
42.6 Falling Object Protective Structure (FOPS)
42.7 Use the Seat Belt
42.8 Fire Extinguisher Location
42.9 Tractors with Cab Suspension
43 Seat Adjustment
43.1 Seat Adjustment and Functions (6M Series)
43.2 CommandARM??Adjust Height
43.3 Instructional Seat for Training Purposes
44 Steering Column
44.1 Adjust the Steering Wheel
45 Mirrors
45.1 External