John Deere 4LZ-13 (S760) Grain Combine, 4YL Operator Manual OMHXE164282TC

Table of Content:

1 Introduction
1.1 Foreword
1.2 Cleaning Guide?Fire Prevention
1.3 A Message to Our Customers
1.4 Emissions Performance and Tampering
1.5 Identification View
2 Safety Features
2.1 Machine Safety Features
3 Safety
3.1 Recognize Safety Information
3.2 Understand Signal Words
3.3 Follow Safety Instructions
3.4 Driving the Machine
3.5 Operator Ability
3.6 Observe Road Traffic Regulations
3.7 Check Machine Safety
3.8 Keep Riders and Children Off Machine
3.9 Ballasting for Safe Ground Contact
3.10 Roadway Transport with Header Attached
3.11 Avoid Electrical Power Lines
3.12 Parking and Leaving the Machine
3.13 Work In Ventilated Area
3.14 Handle Fuel Safely?Avoid Fires
3.15 Prepare for Emergencies
3.16 Handle Starting Fluid Safely
3.17 In Case of Fire
3.18 Avoid Static Electricity Risk When Refueling
3.19 Wear Protective Clothing
3.20 Stay Clear of Harvesting Units
3.21 Keep Hands Away From Knives
3.22 Use Safety Lights and Devices
3.23 Use Seat Belts
3.24 Heated and Ventilated Operator?s Seat
3.25 Instructional Seat
3.26 Transport Combine Safely
3.27 Prevent Machine Runaway or Unexpected Movement
3.28 Practice Safe Maintenance
3.29 Welding Near Electronic Control Units
3.30 Remove Paint Before Welding or Heating
3.31 Avoid Heating Near Pressurized Fluid Lines
3.32 Avoid Contact With Moving Parts
3.33 Cleaning Grain Tank and Removal of Blockages Safely
3.34 Stay Clear of Rotating Drivelines
3.35 Install All Shields and Guards
3.36 Avoid High-Pressure Fluids
3.37 Do Not Open High-Pressure Fuel System
3.38 Service Accumulator Systems Safely
3.39 Protect Against High Pressure Spray
3.40 Follow Tire Recommendations
3.41 Service Tires Safely
3.42 Decommissioning ? Proper Recycling and Disposal of Fluids and Components
3.43 Service Cooling System Safely
3.44 Remove Accumulated Crop Debris
3.45 Support Machine Properly
3.46 Store Attachments Safely
3.47 Service Drive Belts Safely
3.48 Handle Electronic Components and Brackets Safely
3.49 Avoid Backover Accidents
3.50 Emergency Exit
3.51 Handling Batteries Safely
3.52 Clean Exhaust Filter Safely
3.53 Avoid Hot Exhaust
3.54 Rotational Alarm System
3.55 Operator Presence System
3.56 Safety Warning ? AutoTrac? Detected
3.57 Safety Caution ? System Reboot
3.58 Safety Caution ? Software Installation
3.59 Safety Caution ? System Rollback
4 Safety Signs
4.1 Pictorial Safety Signs
4.2 Replace Safety Signs
4.3 Operator’s Manual
4.4 Repair and Maintenance
4.5 Seat Belt
4.6 Parking Brake
4.7 Hydraulic Oil and Gas Under Pressure
4.8 Accumulator
4.9 Avoid Low Hanging Power Lines
4.10 Grain Tank
4.11 Emergency Exit
4.12 Cab/Platform Access Ladder
4.13 Avoid Motor Vehicle Collisions
4.14 Dual Wheels (If Equipped)
4.15 Feeder House Safety Stop
4.16 Feeder House Guard
4.17 Hydraulic Oil and Gas Under Pressure
4.18 Feeder House Inspection Doors
4.19 Feeder House Tilt Frame
4.20 Left-Hand Guard
4.21 Grain Tank Cleanout Doors
4.22 Powered Folding Unloading Auger (If Equipped)
4.23 Battery Box
4.24 Hydraulic Oil and Gas Under Pressure
4.25 Accumulator
4.26 Separator Inspection Door
4.27 Chopper Flying Debris
4.28 Chopper Flying Debris Continued
4.29 Chopper Blades
4.30 Spreader Flying Debris
4.31 Spreader Lock-Out
4.32 Rear Access Ladder and Service Platform
4.33 Avoid Fires
4.34 Grain Tank
4.35 Hydraulic Oil and Gas Under Pressure
4.36 Accumulator
4.37 Cooling System
4.38 Avoid Grain Tank
4.39 Avoid Clean Grain Loading Auger
4.40 Tailings Elevator Sensor Laser
4.41 Rotary Screen Door and Radiator Fan
4.42 Clean Grain Loading Auger
4.43 Clean Grain Elevator
4.44 Stone Trap
4.45 Hydraulic Oil and Gas Under Pressure
4.46 Accumulator
4.47 Feeder Conveyor Drive Guard
4.48 Feeder House Feed Plate Latch
4.49 Starter
4.50 Handle Fuel Safely?Avoid Fires
4.51 Exhaust Temperature
4.52 Fall From Engine Covers
4.53 Air Compressor System (If Equipped)
4.54 Air Compressor Reservoir (If Equipped)
5 Operator?s Station
5.1 Radio Types (Optional)
5.2 After Market Radios
5.3 Program Radio for Local Area Frequency
5.4 Radio Controls
5.5 Antenna
5.6 Communications/CB Radio Wiring
5.7 Communications/CB Radio Mounting
5.8 Cab Ladder Positions
5.9 Fire Extinguisher
5.10 Fire Extinguisher Locations
5.11 Handrails and Right-Hand Landing Access
6 Break-In Service
6.1 Breaking-In Engine
6.2 Belt Drives Adjustment – First 50 Hours
6.3 Break-In Check Before First 100 Hours
6.4 Break-In Service After 100 Hours
7 Prestarting Checks
7.1 Engine Oil Level
7.2 Hydrostatic/Hydraulic Oil Level
7.3 Coolant Level
7.4 Fuel System
7.5 Fuel Tank Breather
7.6 Engine Air Scoop Positions
7.7 Position Engine Air Scoop (Standard Field Position)
7.8 Position Engine Air Scoop (Extended Field Position)
7.9 Position Engine Air Scoop (Transport Position)
7.10 Cleaning Engine Compartment
8 Operating the Engine
8.1 Clean Exhaust Filter Safely
8.2 Avoid Hot Exhaust
8.3 Required Machine Stop Warning
8.4 Starting the Engine
8.5 Stopping the Engine
8.6 Handle Starting Fluid Safely
8.7 Cold Weather Starting Aid (If Equipped)
8.8 Coolant Heater
9 CommandCenter? Display Information
9.1 Determine Machine Specific Information
9.2 Generation 4 Display
10 CommandCenter? Display Applications
10.1 CommandCenter? Display Applications
11 Controls Setup
11.1 Access Controls Setup
11.2 Controls Setup Overview
11.3 Multi-Function Lever – Controls Setup
11.4 Multi-Function Lever
11.5 CommandARM? – Controls Setup
11.6 CommandARM?
11.7 Create Single Position Assignments
11.8 Create Dual Position Assignments
11.9 Scroll Button
11.10 Application Assignments
11.11 Function Assignments
12 Residue Management
12.1 Access Residue Management
12.2 Residue Management Main Page
12.3 Residue Mode
12.4 Separator Vane
12.5 Width
12.6 Speed
12.7 Direction
12.8 Swap
12.9 Out of Cab Adjustments
12.10 Knife Bank
12.11 Auto Swap
13 Header
13.1 Access Header
13.2 Header
13.3 Header Details
13.4 Width
13.5 Width Corn Head
13.6 Row Width
13.7 Minimum Reel Speed
13.8 Work Recording
13.9 Hours
13.10 Raise/Lower Speed
13.11 Tilt Speed
13.12 Height Sensitivity
13.13 Tilt Sensitivity
13.14 Fore/Aft Tilt
13.15 Auto Header Control
13.16 Control Preview
13.17 Header Automation
13.18 Height Resume
13.19 Height Sensing?Off Ground
13.20 Height Sensing?On Ground
13.21 Feeder House Float
13.22 Lateral Tilt
13.23 Resume Preferences
13.24 Dial?A?Speed? Resume
13.25 Fore/Aft Resume
13.26 Reel Position Resume
13.27 Deck Plate Position Resume
13.28 Cutterbar Position Resume
13.29 HydraFlex? Pressure
13.30 Draper Belt Speed
13.31 Draper Float Position
13.32 Cutterbar Tilt
13.33 Deck Plate Spacing
13.34 Backshaft Speed
13.35 Cutterbar Position
13.36 Advanced Settings
13.37 Limp Home Mode
13.38 Cutterbar Position Wizard
14 Grain Handling
14.1 Access Grain Handling
14.2 Grain Handling Main Page
14.3 Advanced Settings
14.4 Advanced Settings | Grain Level Auto Beacon
14.5 Advanced Settings | Tank Unloading Offset
14.6 Advanced Settings | Custom Level Alarm
14.7 Grain Level
14.8 Moisture Settings
14.9 Moisture Alarm
14.10 Moisture Correction
14.11 Status Center
15 Folding
15.1 Access Folding
15.2 Folding Main Page
15.3 Grain Tank Covers
15.4 Folding Auger Tip
15.5 Folding Corn Head (Without Position Sensors)
15.6 Folding Corn Head (With Position Sensors)
15.7 Manual Control
16 Harvest Settings
16.1 Access Harvest Settings
16.2 Harvest Settings Main Page
16.3 Load Harvest Settings
16.4 Load Harvest Settings | Preset
16.5 Load Harvest Settings | Threshing Conditions
16.6 Load Harvest Settings | Straw Conditions
16.7 Load Harvest Settings | Save Preset
16.8 Load Harvest Settings | Save Preset | Factory Default
16.9 Load Harvest Settings | Save Preset | Custom Preset
16.10 Load Harvest Settings | Effects of Crop Change
16.11 Current Settings | Threshing Clearance
16.12 Current Settings | Threshing Speed
16.13 Current Settings | Cleaning Fan
16.14 Current Settings | Chaffer Clearance
16.15 Current Settings | Sieve Clearance
16.16 Current Settings | Outside Configuration
16.17 Current Settings | Adjustment States
16.18 Advanced Settings
16.19 Advanced Settings | Separator Resolution
16.20 Advanced Settings | Shoe Resolution
16.21 Performance Target
17 Engine
17.1 Access Engine
17.2 Engine Main Page
17.3 Engine Power
17.4 Debris Management Filter Capacity
17.5 Air Compressor
17.6 Air Compressor Status
18 HVAC
18.1 Access HVAC
18.2 Heating, Ventilation, and Air Conditioning (HVAC) Main Page
18.3 Set Temperature
18.4 Fan Speed
18.5 Air Flow Mode
18.6 Air Conditioning (A/C)
18.7 Outside Temperature
19 Transmission
19.1 Access Transmission
19.2 Transmission Main Page
19.3 Max Speed 1 and 2
19.4 Advanced Settings ProDrive?
19.5 Advanced Settings ProDrive? Tow Mode
19.6 Advanced Settings ProDrive? Limp Home Mode
19.7 Advanced Settings Push Button
19.8 Multi-Function Lever Sensitivity
20 Lights
20.1 Access Lights
20.2 Lights Main Page
20.3 Work Lights Preset 1?Low Beam
20.4 Work Lights Preset 2?Low Beam
20.5 Work Lights Preset 1?High Beam
20.6 Work Lights Preset 2?High Beam
20.7 Exit Lights
20.8 Work Light Controls
20.9 Advanced Settings
21 Phone
21.1 Access Phone
21.2 Phone Main Page
21.3 Add Favorite Page
21.4 Advanced Settings
21.5 Edit Favorite Page
21.6 Manage Devices
21.7 Pairing Bluetooth? Device
21.8 Phone Favorites Page
21.9 Recent Calls
22 Calibrations
22.1 Access Calibrations and Procedures
22.2 Calibrations and Procedures Overview
22.3 Mass Flow Vibration
22.4 Mass Flow Vibration Calibration Procedure
22.5 Moisture Sensor
22.6 Moisture Sensor Procedure
22.7 Threshing Clearance (STS Electric)
22.8 Threshing Clearance (STS Electric) Calibration Procedure
22.9 Yield Calibration
22.10 Yield | Calibration Quality
22.11 Yield | Status Indicator
22.12 Yield | Record Sample
22.13 Yield | Match Scale Weight
22.14 Yield | Advanced Settings
22.15 Yield | Calibration Quality Indicator
22.16 Yield | Collected Sample Status
22.17 Yield | Mass Flow Rate
22.18 Yield | Weight Indicator
22.19 Yield | Recording Status
22.20 Yield | Reset
22.21 Yield | Edit/Select Calibration
22.22 Yield | Advanced Edit
22.23 Yield | Delete Unused Samples
22.24 ActiveYield?
22.25 ActiveYield? | Status Indicator
22.26 ActiveYield? | Advanced Settings
22.27 ActiveYield? | Reset
22.28 Chassis Tilt
22.29 Chassis Tilt Calibration Procedure
22.30 Threshing Clearance (Hydraulic)
22.31 Threshing Clearance (Hydraulic) Calibration Procedure
22.32 Unloading Auger Engage
22.33 Unloading Auger Engage Calibration Procedure
22.34 Deck Plate Spacing
22.35 Deck Plate Spacing Calibration Procedure
22.36 Feeder House Raise Speed
22.37 Feeder House Raise Speed Calibration Procedure
22.38 Header Calibration
22.39 Header Calibration Procedure
22.40 Extendable Platform Header Self-Test
22.41 Extendable Platform Header Self-Test Calibration Procedure
22.42 Feeder House Tilt Fore/Aft Range
22.43 Feeder House Tilt Fore/Aft Range Calibration Procedure
22.44 Feeder House Lateral Tilt Range
22.45 Feeder House Lateral Tilt Range Calibration Procedure
22.46 Feeder House Lateral Tilt Speed
22.47 Feeder House Lateral Tilt Speed Calibration Procedure
22.48 Wings (Folding Corn Head)
22.49 Wings (Folding Corn Head) Calibration Procedure
22.50 Reel and Cutterbar Position
22.51 Reel and Cutterbar Position Calibration Procedure
22.52 Reel Position
22.53 Reel Position Calibration Procedure
22.54 Amber Flasher
22.55 Amber Flasher Calibration Procedure
22.56 Concave Air Removal
22.57 Concave Air Removal Calibration Procedure
22.58 Concave Leveling
22.59 Concave Leveling Calibration Procedure
23 Combine Overview
23.1 Combine Overview
23.2 Front Console
23.3 Corner Post Display
23.4 CommandARM? Console and Display
23.5 Multi-function Lever
23.6 Navigation Bar
23.7 Right-Hand Cab Items
23.8 Left-Hand Cab Items
23.9 Overhead Controls
23.10 Seat Controls
23.11 Key Switch
23.12 Adjusting Steering Wheel
23.13 Operate Lights
23.14 Operate Turn Signals, Horn and High and Low Beam
23.15 Operate Windshield Wiper and Washer
23.16 Operate Ether Injection (If Equipped)
23.17 ComfortCommand? Operators Seat (Basic Seat)
23.18 ComfortCommand? Operators Seat (Premium Cloth Seat)
23.19 ComfortCommand? Operators Seat (Premium Leather Seat)
23.20 Seat Belts
23.21 Instructional Seat
23.22 Harvesting Controls
23.23 HVAC
23.24 Radio
23.25 Engine and Ground Drive
23.26 Lights
23.27 Console and Display
23.28 Feeder House Reverser
23.29 Belt Pickup Cleanout
23.30 Header Engage
23.31 Separator Engage
23.32 Threshing Clearance Adjust
23.33 Threshing Speed Adjust
23.34 Cleaning Fan Speed Adjust
23.35 Chaffer Adjust
23.36 Sieve Adjust
23.37 Seek
23.38 Push Button Shift Gear (If Equipped)
23.39 ProDrive? (If Equipped)
23.40 Road Transport Disconnect
23.41 Four-Wheel Drive (If Equipped)
23.42 Differential Lock (If Equipped)
23.43 Park Brake
23.44 Fuel Level Indicator
23.45 Quick Stop Switch
23.46 Unloading Auger Swing Switch
23.47 Unloading Auger Drive Switch
23.48 AutoTrac? Resume Button (If Equipped)
23.49 Header Raise Lower and Tilt (If Equipped) Switch
23.50 Reel Raise and Lower and Reel Fore and Aft (If Equipped)
23.51 Feeder House Backshaft Speed and Adjustable Corn Head Deck Plates (If Equipped)
23.52 Header Activation Buttons
23.53 VisionTrak?
24 Radio
24.1 Access Audio
24.2 Audio Main Page
24.3 Premium Radio Auxiliary Tab
24.4 Premium Radio Bluetooth? Tab
24.5 AM, FM, Weather Channel Tab
24.6 Premium Radio USB Tab
24.7 Premium Radio XM Tab (If Equipped)
24.8 Premium Radio CD Tab (If Equipped)
24.9 Advanced Settings
25 Combine Advisor?
25.1 Access Combine Advisor?
25.2 Combine Advisor? Main Page
25.3 Advanced Settings
25.4 Grain System Video
25.5 History
25.6 Performance
25.7 Active
25.8 Completed
25.9 Offset Details
25.10 Adjustment Details
25.11 Lens Debris
25.12 Automation Status
25.13 HarvestSmart? Settings
25.14 Speed Limit
25.15 Response Aggressiveness
25.16 HarvestSmart? | Automation
25.17 Engine Power Target
25.18 Active Terrain Adjustment? Settings
25.19 Uphill Sensitivity
25.20 Downhill Sensitivity
25.21 HarvestSmart? Status
25.22 Active Terrain Adjustment? Status
25.23 Auto Maintain Status
25.24 Optimize Performance
25.25 Offset Tuning Chaffer
25.26 Offset Tuning Sieve
25.27 Cannot Maintain Target
25.28 Offset Tuning Cleaning Fan
25.29 Set Performance Target
25.30 Performance Issues
25.31 Separator Losses
25.32 Shoe Losses
25.33 Unthreshed Losses
25.34 Broken Grain
25.35 Light Foreign Material
25.36 Heavy Foreign Material
25.37 Unthreshed Material
25.38 Straw Quality Issues
25.39 Excess Tailings
25.40 Solutions
25.41 Ground Speed Adjustment
25.42 Separator Vane Adjustments
25.43 Out-of-Cab Adjustments
25.44 Auto Maintain Settings
25.45 Response Aggressiveness
25.46 Grain Loss Sensitivity
25.47 Broken Grain Sensitivity
25.48 Foreign Material Sensitivity
26 Lights and Signals
26.1 Lighting Locations (Front and Rear View Lights)
26.2 Lighting Locations (Front and Rear View Lights Continued)
26.3 Lighting Locations (Front and Rear View Lights Continued)
26.4 Lighting Locations (Left and Right Side View Lights)
26.5 Lighting Locations (Left and Right Side View Lights Continued)
26.6 Lighting Locations (Left and Right Side View Lights Continued)
26.7 Driving Lights (Eurasian Economic Union)
26.8 Lighting Delay/Timeout
27 Feeder House
27.1 Hydraulic Cylinder Safety Stop
27.2 Feeder House Side Shields
27.3 Feeder House Doors
27.4 Feed Accelerator Top Access Door
27.5 Feeder House Bottom Door and Feed Plate Seal Support (Style A)
27.6 Feeder House Bottom Door and Feed Plate Seal Support (Style B)
27.7 Stone Trap
27.8 Adjust and Set Feeder House Fore/Aft Tilt Frame (Manual Tilt)
27.9 Set Feeder House Fore/Aft Tilt Frame Zero Point (Hydraulic Tilt) (If Equipped)
27.10 Feeder House Conveyor Chain?Adjusting
27.11 Feeder House Conveyor Chain Links?Removing
27.12 Feeder House Drum (Manual Tilt)?Height Adjustment
27.13 Feeder House Drum (Hydraulic Tilt) (If Equipped)?Height Adjustment
27.14 Feeder House Conveyor Speed?Changing
27.15 Feeder House Conveyor Drive Chain Links?Removing
27.16 Feeder House Conveyor Drive Chain?Adjusting
27.17 Feeder House Top Shaft Sprockets
27.18 Feeder House Variable Speed Drive Belt?Replacing
27.19 Feeder House Variable Speed Drive Belt?Adjusting
27.20 Header Reel/Belt Pickup Pump Belt (Variable Speed Feeder House)?Replacing
27.21 Header Reel/Belt Pickup Pump Belt (Variable Speed Feeder House)?Adjusting
27.22 Feeder House Fixed Speed Drive Belt?Replacing
27.23 Feeder House Fixed Speed Drive Belt?Adjusting
27.24 Header Reel/Belt Pickup Pump Belt (Fixed Speed Feeder House)?Replacing
27.25 Header Reel/Belt Pickup Pump Belt (Fixed Speed Feeder House)?Adjusting
27.26 CommandTouch Multi-Speed Feeder House Drive Belt?Replacing
27.27 CommandTouch Multi-Speed Feeder House Drive Belt?Adjusting
27.28 Header Reel/Belt Pickup Pump Belt (CommandTouch Multi-Speed Feeder House)?Replacing
27.29 Header Reel/Belt Pickup Pump Belt (CommandTouch Multi-Speed Feeder House)?Adjusting
27.30 Manual Tilt Indicator (Lateral Tilt System)
27.31 Attach Multicoupler and Single Point Latching
27.32 Attaching and Detaching Header from Feeder House
27.33 Single Point Latching?Adjusting
27.34 Level Land Feeder House Lower Cable End?Adjusting
27.35 Level Land Feeder House?Shim Adjusting
27.36 Feeder House Latching Pins (Cleanout)
27.37 Feeder House Manual Unlatching
27.38 Shear Screw Location
28 Shields
28.1 Gull Wing Doors
28.2 Gull Wing Door Cylinder Adjustment
28.3 Toolbox (If Equipped)
28.4 Left-Hand Side Shields
28.5 Right-Hand Side Shields
28.6 Separator Covers
29 Separator
29.1 Standard Feed Accelerator Wear Strips?Replacing
29.2 Tough Crop Feed Accelerator Wear Strips?Replacing
29.3 Tine Feed Accelerator Wear Strips?Replacing
29.4 Tine Feed Accelerator Comb Floor (Rice Machines)
29.5 Tine Feed Accelerator Comb Floor (Rice Machines)?Removing
29.6 Feed Accelerator Belt?Replacing
29.7 Feed Accelerator Belt?Adjusting
29.8 Standard Speed High Capacity Feed Accelerator?Changing Speed
29.9 High Speed High Capacity Feed Accelerator?Changing To Slow Speed
29.10 Concave Recommendations
29.11 Concave Types
29.12 Separator Grate Spacers
29.13 Separator Grate Types
29.14 Separator Grate Covers (If Equipped)
29.15 Separator Grate Interrupters (If Equipped)
29.16 Separator Grate Interrupter Locations (If Equipped)
29.17 Separator Rail Liners (If Equipped)
29.18 Concave Sector Gear Shear Bolts (Standard Concave Adjust)
29.19 Concave Sections (Standard Concave Adjust)?Remove and Install
29.20 Concave Sections (Active Concave Isolation)?Remove and Install
29.21 Concave Leveling (Standard Concave Adjust)
29.22 Concave Leveling (Active Concave Isolation)
29.23 Separator Top Cover Vanes (If Equipped)
29.24 Threshing Elements and Tines (TriStream Rotor)?Remove and Install
29.25 Threshing Element and Separator Tine Location (TriStream Rotor Tough Grain Configuration)
29.26 Threshing Element and Separator Tine Location (TriStream Rotor Dense Pack Configuration)
29.27 Threshing Elements and Tines (Variable Stream Rotor)?Remove and Install
29.28 Threshing Element and Separator Tine Location (Variable Stream Rotor Standard Configuration)
29.29 Threshing Element and Separator Tine Location (Variable Stream Rotor Dense Pack Configuration)
29.30 Posi-Torq? Separator?Dual-Range
29.31 Separator Drive Sheave Gap?Adjusting
29.32 Separator Variable Drive Belt?Replacing
29.33 Auger Bed Dividers
29.34 Discharge Beater Belt?Adjusting
29.35 Discharge Beater Belt?Replacing
29.36 Discharge Beater Wear Strips?Replacing (5 and 10 Wing Style)
29.37 Standard Discharge Beater Wear Strips?Replacing (8 Wing Style)
29.38 Tough Crop Discharge Beater Wear Strip?Replacing
29.39 Overshot Beater Belt (If Equipped)?Adjusting
29.40 Overshot Beater Belt (If Equipped)?Replacing
29.41 Standard Overshot Beater (If Equipped)?Wing Replacing
29.42 Tough Crop Overshot Beater (If Equipped)?Wing Replacing
29.43 Countershaft Right-Hand Front Belt?Adjusting
29.44 Countershaft Right-Hand Front Belt?Replacing
29.45 Countershaft Right-Hand Rear Belt?Adjusting
29.46 Countershaft Right-Hand Rear Belt?Replacing
29.47 Cleaning Shoe Air Chutes and Access Door
29.48 Cleaning Shoe Auger Gears?Manual Cleanout Door (If Equipped)
29.49 Cleaning Shoe Auger Gears?Cleanout Door (If Equipped)
29.50 Shoe, Fan, and Conveyor Auger Belt?Adjusting
29.51 Shoe, Fan, and Conveyor Auger Belt?Replacing
29.52 Cleaning Fan Actuator (Without Active Terrain Adjustment?)?Adjusting
29.53 Cleaning Fan Actuator (Active Terrain Adjustment?)?Adjusting
29.54 Cleaning Fan Belt (Without Active Terrain Adjustment?)?Replacing
29.55 Cleaning Fan Belt (Active Terrain Adjustment?)?Replacing
29.56 Adjustable Front Chaffer (If Equipped)
29.57 Fixed Front Chaffer
29.58 Chaffer and Sieve?Measuring
29.59 General-Purpose Chaffer 30 mm (1-3/16 in)
29.60 Deep-Tooth Chaffer 41 mm (1-5/8 in)
29.61 Premium Corn Chaffer 41 mm (1-5/8 in)
29.62 High-Performance Chaffer 30 mm (1-3/16 in)
29.63 General Purpose Sieve 30 mm (1-3/16 in)
29.64 Deep-Tooth Sieve 30 mm (1-3/16 in)
29.65 Chaffer/Sieve Adjusting Switch
29.66 Dual Zone Adjust Rear Chaffer?Adjusting
29.67 Chaffer/Sieve Elements?Remove and Install
29.68 Chaffer/Sieve/Return Pan Assemblies
29.69 Chaffer/Sieve Motor?Manual Adjust
29.70 Clean Grain Elevator Belt?Adjusting
29.71 Clean Grain Elevator Belt?Replacing
29.72 Clean Grain Elevator Conveyor Chain?Adjusting
29.73 Clean Grain Elevator Wear Plates and Door (If Equipped)
29.74 VisionTrak? Operational Checks
29.75 ActiveVision? Clean Grain Elevator Camera (If Equipped)
29.76 ActiveVision? Tailings System Camera (If Equipped)
29.77 Tailings System Elevator Sensors
29.78 Tailings System Elevator Paddles
29.79 Tailings Elevator Drive Belt?Adjusting (Style A)
29.80 Tailings System Elevator Paddle Chain?Adjusting
29.81 Upper Tailings Auger Drive Chain?Adjusting (Style A)
29.82 Tailings System Drive Belt?Adjusting (Style B)
29.83 Tailings System Drive Belt?Replacing (Style B)
29.84 Tailings System Drive Chain?Adjusting (Style B)
29.85 Tailings System Drive Chain?Replacing (Style B)
29.86 Tailings System Wear Strips and Rasp Bars?Remove and Install (Style B)
29.87 Tailings System Wear Strips and Rasp Bars?Adjusting (Style B)
29.88 Tailings System Return Concave?Adjusting (Style B)
29.89 Tailings System Auger Cleanout Door (Style B)
29.90 Drive Belts?Left-Hand
29.91 Drive Belts?Right-Hand (Style A)
29.92 Drive Belts?Right-Hand (Style B)
29.93 Feed Accelerator?Unplugging
29.94 Separator?Unplugging
29.95 Discharge Beater?Unplugging
30 Residue Management
30.1 Residue Material Handling Option (Intermediate/Deluxe Residue)
30.2 Residue Material Handling Option (Premium Residue)
30.3 Residue Material Handling Option (Straw Spreader)
30.4 General Windrowing Information (Intermediate/Deluxe Residue)
30.5 Crop Diverter Vanes?Adjusting
30.6 General Windrowing Information (Premium Residue)
30.7 Windrow Convergence Rakes
30.8 Tailboard?Adjusting (Deluxe Residue)
30.9 Tailboard Vanes (Manual Adjust)?Adjusting (Deluxe Residue)
30.10 Tailboard Vanes (Electric Motor)?Adjusting (Deluxe Residue)
30.11 Tailboard Vanes (Manual Adjust)?Factory Settings (Deluxe Residue)
30.12 Tailboard Vanes (Electrical Adjust)?Factory Settings (Deluxe Residue)
30.13 PowerCast? Tailboard?Adjusting (Optional)
30.14 PowerCast? Tailboard Blade?Replacing (Optional)
30.15 PowerCast? Tailboard (Optional) Rear Shrouds
30.16 Crop Diverter
30.17 Air Chutes
30.18 Overshot Beater Floor (If Equipped)?Removing (Premium Residue)
30.19 Chopper Controller Bar (Optional)
30.20 Chopper Stationary Knife Bank (Without Electric Actuator)?Adjusting
30.21 Chopper Stationary Knife Bank (Electric Actuator)?Removing (If Equipped)
30.22 Chopper Stationary Knife Bank (Electric Actuator)?Installing (If Equipped)
30.23 Chopper Stationary Knives (Without Electric Actuator)?Replacing
30.24 Chopper Stationary Knives (Electric Actuator)?Replacing
30.25 Chopper Access Door
30.26 Fine Cut Chopper Blades?Replacing and Configuration
30.27 Extra Fine Cut Chopper Blades?Replacing and Configuration
30.28 Middle Splitter Knife?Replacing (Advanced PowerCast? Tailboard)
30.29 Chopper Blades?Centering
30.30 Chopper Adjusting Switch
30.31 Chopper Drive Speeds?Changing
30.32 Tailboard Vanes?Adjusting (Intermediate/Premium Residue)
30.33 Tailboard Vanes (Electric Motor)?Adjusting (Intermediate/Premium Residue)
30.34 Tailboard Vanes (Electrical Adjust)?Factory Settings (Intermediate/Premium Residue)
30.35 Advanced PowerCast Spreader Disks?Replacing
30.36 Spreader (General Information)
30.37 Spreader?Windrow Position
30.38 Spreader?Lowering
30.39 Spreader Disks (Single Speed)?Replacing
30.40 Spreader Disks (Dual Speed)?Replacing
30.41 Wide Spread Straw Spreader (Optional)
30.42 Chopper Drive Belt Tension?Adjusting
30.43 Chopper Belt?Replacing
30.44 Chopper Jackshaft Belt?Adjusting
30.45 Chopper Jackshaft Belt?Replacing (Style A)
30.46 Chopper Jackshaft Belt?Replacing (Style B)
31 Grain Tank and Unloading System
31.1 Grain Tank/Engine Ladder
31.2 Grain Tank Sample Trough
31.3 Grain Tank Drain Holes
31.4 Grain Tank Fill Sensors?Adjusting
31.5 Grain Tank Covers (If Equipped)?Operating
31.6 Grain Tank Covers (If Equipped)?Adjusting
31.7 Grain Tank Cross Auger Covers
31.8 ActiveYield? (If Equipped) Cross Auger Covers?Removing
31.9 ActiveYield? (If Equipped) Sensor Locations
31.10 Shear Bolt Location
31.11 Unloading Auger Drive Shear Bolt
31.12 Grain Tank Loading Auger Deflector
31.13 Grain Tank Loading Auger (Grain Tank Extensions)?Folding
31.14 Grain Tank Loading Auger (Grain Tank Covers)?Adjusting
31.15 Mass Flow Sensor Plate (Grain Tank Extensions)?Cleaning
31.16 Mass Flow Sensor Plate (Grain Tank Covers)?Cleaning
31.17 Unloading Auger Drive Chain?Adjusting
31.18 Unloading Auger Drive Chain Links?Removing
31.19 Unloading Auger Cradle Support?Adjusting
31.20 Unloading Auger Position?Adjusting
31.21 Unloading Auger Lock Arm Positions
31.22 Unloading Auger Drive Belt?Replacing (Style A)
31.23 Unloading Auger Drive Belt?Replacing (Style B)
32 Service – Electrical System
32.1 Welding Near Electronic Control Units
32.2 Keep Electronic Control Unit Connectors Clean
32.3 Observe Electrical Precautions
32.4 Basic Electrical Component Handling / Precautions for Vehicles Equipped with Computer Controlled Systems
32.5 Handling Batteries Safely
32.6 Batteries?Safe Installation
32.7 Battery Cables?Connecting
32.8 Batteries?Charging
32.9 Batteries?Checking Specific Gravity
32.10 Batteries?Connecting Booster
32.11 Batteries?Removing and Installing (Style A)
32.12 Batteries?Removing and Installing (Style B)
32.13 Battery Disconnect Switch
32.14 Machine Fuse Center
32.15 Inline Fuses
32.16 Cab Fuse Center
32.17 Video Safety
32.18 Video Interface Capability
32.19 Adjust Cameras (If Equipped)
32.20 Safety Rules When Replacing Halogen Bulbs
32.21 Cab Headlight Bulb?Replacing
32.22 Cab Headlights?Adjusting
32.23 Cab Halogen Light Bulb?Replacing
32.24 Cab Halogen Lights?Adjusting
32.25 Halogen Bulb Fascia Lights (If Equipped)?Replacing
32.26 Light Emitting Diode (LED) Fascia Lights (If Equipped)?Replacing
32.27 Lower Driving Light Bulb (If Equipped)?Replacing
32.28 Lower Driving Light Bulb (If Equipped)?Adjusting
32.29 Light Emitting Diode (LED) Lights (Optional)?Replacing
32.30 Light Emitting Diode (LED) Lights (Optional)?Adjusting
32.31 Replace Beacon Lights (Style A)
32.32 Replace Beacon Light (Style B)
32.33 Halogen Bulb Work Lights (If Equipped)?Replacing
32.34 Light Emitting Diode (LED) Work Lights (If Equipped)?Replacing
32.35 Halogen Bulb Side Finder Lights and Cleaning Shoe Lights (If Equipped)?Replacing
32.36 Light Emitting Diode (LED) Side Finder Lights and Cleaning Shoe Lights (If Equipped)?Replacing
32.37 Hazard/Marker Lights, Marker/Brake Lights, and Rear Hazard Lights?Replacing
32.38 Cab Interior Light?Replacing
32.39 Map Light?Replacing
33 Ground Drive and Rear Axle
33.1 Service Tires Safely
33.2 Roadway Transport with Header Attached
33.3 Care and Service of Tires
33.4 Basic Tire Information
33.5 Tire Tread Types
33.6 Tire Pressure
33.7 Front and Rear Tire Information
33.8 Drive Wheel Starter Stud
33.9 Drive Wheel Bolt Torque
33.10 Front Drive Wheel Offset
33.11 Preparing Dual Wheels for Transport or Service
33.12 Remove Front Wheels
33.13 Install Front Wheels
33.14 Rear Wheel Bolt Torque
33.15 Using Liquid Weight
33.16 Ballast Requirements
33.17 Jack Pocket Locations Decal
33.18 Jack Pocket Locations
34 Transporting
34.1 Roadway Transport with Header Attached
34.2 Driving Machine on Roads
34.3 Back-Up Alarm
34.4 Transporting Machine on a Trailer
34.5 Machine Tie Down Locations Decal
34.6 Machine Tie Down Locations
34.7 Jack Pocket Locations
34.8 Transport Information
34.9 Towing Machine (Mechanical Shift Transmission Machines)
34.10 Manual Trailer Hitch?Attaching (Standard)
34.11 Semi-Automatic Trailer Hitch?Attaching (Optional)
34.12 Front Tow Hook
34.13 Rear Tow Hook
35 Harvesting Hints
35.1 Operation at Low Temperatures
35.2 Harvesting Tips
35.3 Auto Header Control Combinations
35.4 Change Tire Radius Code
35.5 Single Point Yield Calibration Or Multi-Point Yield Calibration
36 Crop Settings
36.1 Alfalfa / Barley
36.2 Canola / Chickpeas
36.3 Corn (Dry) / Corn (Wet)
36.4 Corn Cob Mix / Edible Beans
36.5 Flax / Grass Seed
36.6 Guar (Cluster Beans) / Lentils
36.7 Lupins / Millet
36.8 Mustard / Navy Beans
36.9 Oats / Peas
36.10 Popcorn / Rape Seed (Dry)
36.11 Rape Seed (Green) / Rice
36.12 Rye / Safflower
36.13 Sorghum / Soybeans
36.14 Sunflower / Triticale
36.15 Wheat Difficult / Wheat Normal
36.16 Footnotes Description Page
36.17 Concave Recommendations
36.18 Power Shutdown Procedure
36.19 Payable Moisture and Density Chart
36.20 Standard Weights Chart
37 Fire Prevention
37.1 Recommended Fire Preventions
37.2 Fire Extinguisher Operation
37.3 C