Table of Content:
1 Introduction
1.1 Foreword
1.2 Product View
1.3 A Message to Our Customers
1.4 Preliminary Checks
1.5 Regions and Country Versions
1.6 Machine Overview
2 Safety
2.1 Understand Signal Words
2.2 Follow Safety Instructions
2.3 Prepare for Emergencies
2.4 Wear Protective Clothing
2.5 Practice Safe Maintenance
2.6 Park Machine Safely
2.7 Remove Paint Before Welding or Heating
2.8 Avoid Heating Near Pressurized Fluid Lines
2.9 Avoid High-Pressure Fluids
2.10 Keep Riders Off Machine
2.11 Use Safety Lights and Devices
2.12 Use Seat Belt Properly
2.13 Operate the Plow Safely
2.14 Safe Transport of the Disk Plow
2.15 Decommissioning — Proper Recycling and Disposal of Fluids and Components
3 Safety Signs
3.1 Read Safety Signs Carefully
3.2 Cylinder Adjustment
3.3 Detach Using Support Stand
3.4 Reversing
3.5 Transport
3.6 Reversing Plow
3.7 Follow Safe Service Practices
3.8 Hydraulic Cylinder
4 Preparing the Tractor
4.1 Tractor Size
4.2 Tire Pressure
4.3 Use Correct Hose Tips
4.4 Adjusting Rate of Cylinder Operation (Flow Control Setting)
4.5 Position Drawbar
4.6 Adjusting Tractor Hitch
4.7 Adjusting Center Link
4.8 Using Load/Depth Control
4.9 Using Position Control
4.10 Using Float Position
4.11 Using Draft Control
4.12 Adjusting Rate of Drop
4.13 Front and Rear Wheel Setting
4.14 Front Wheel Setting
4.15 Tire Inflation
4.16 Determining Front Ballast
4.17 Rear Wheel Weighting
4.18 Front Ballast-Mechanical Front Wheel Drive (MFWD) Tractors
5 Preparing the Machine
5.1 Checking and Lubricating Plow
5.2 Bolts and Set Screws
5.3 Before Going to the Field
6 Operating the Machine
6.1 Before Going to the Field
6.2 In the Field
6.3 Raising and Lowering
6.4 Depth of Plowing
6.5 Reversing the Bottoms
6.6 Landsides for the Side Draft Control
6.7 5, 6, and 7 Bottoms Plow Landside
6.8 8 Bottoms Plow Landside
6.9 5 and 6 Bottoms Plow Landside
6.10 Bolt Standards
6.11 Safety Trip Standards (Optional)
6.12 Adjusting Safety Trip
6.13 Safety Trip Cleaning
6.14 Adjusting Rear Gauge Wheel
7 Attaching and Detaching
7.1 Using Load/Depth Control
7.2 Using External Raise/Lower Switch
7.3 Using External Raise/Lower Switch
7.4 Using Hitch Control Lever and Raise/Lower Switch
7.5 Adjusting Height Limit
7.6 Attaching Integral Plow
7.7 Using Correct Hitch Category
7.8 Hitch Conversion Quick Coupler
7.9 Connecting Cylinder Hoses
7.10 Disconnecting Cylinder Hoses
7.11 Attaching Implement Warning Light (if Equipped)
7.12 Checking Hydraulic System
7.13 Detaching the Plow
8 Transporting Machine
8.1 Transporting the Plow
8.2 Use Safety Lights and Devices
9 Assembly
9.1 Set up Time
9.2 General Information
9.3 Putting Main Frame on Stands
9.4 Installing Plow Support Stand
9.5 Installing Landsides to Bottoms
9.6 Installing Bottoms
9.7 Position of Safety Trip on Moldboard Plow
9.8 Attaching Extensions
9.9 Reversing Mechanism
9.10 Verification
9.11 Attaching Rear Gauge Wheel
9.12 Slow Moving Vehicle (SMV Emblem)
9.13 Front Gauge Wheels
9.14 Attaching Warning Light Kit
10 Attachments
10.1 Front Gauge Wheels
11 Troubleshooting
11.1 Troubleshooting
12 Lubrication and Maintenance
12.1 Grease
12.2 Lubricating Safety Trip or Tension Bolt
12.3 Lubricating Pivot Pin
12.4 Lubricating Reversion Arm
12.5 Lubricating Gauge Wheel Axle
12.6 Lubricating Reversion Roller
12.7 Lubricating Front Gauge Wheel
13 Service
13.1 Bottoms
13.2 Shares
13.3 Landsides
13.4 Wheel Bearings
13.5 Service at the Beginning of the Season
13.6 Reversing Mechanism
13.7 Service Tire Safely
13.8 Unified Inch Bolt and Screw Torque Values
13.9 Metric Bolt and Screw Torque Values
14 Storage
14.1 Keep Your Plow Prepared
15 Specifications
15.1 Specifications
15.2 Specifications
15.3 Product Identification Number
16 John Deere Service Keeps You On The Job
16.1 John Deere Parts
16.2 The Right Tools
16.3 Well-Trained Technicians
16.4 Prompt Service