John Deere 8rt Series Tractors Operator Manuals OMRE591931

Table of Content:

1 Introduction
1.1 Foreword
1.2 Emissions Performance and Tampering
1.3 Look For Supplemental Information
1.4 Trademarks
2 Glossary
2.1 Glossary of Terms
3 Safety
3.1 Recognize Safety Information
3.2 Understand Signal Words
3.3 Follow Safety Instructions
3.4 Prepare for Emergencies
3.5 Wear Protective Clothing
3.6 Protect Against Noise
3.7 Handle Fuel Safely?Avoid Fires
3.8 Fire Prevention
3.9 In Case of Fire
3.10 Avoid Static Electricity Risk When Refueling
3.11 Use Foldable ROPS and Seat Belt Properly
3.12 Stay Clear of Rotating Drivelines
3.13 Use Steps and Handholds Correctly
3.14 Read Operator?s Manuals for ISOBUS Controllers
3.15 Use Seat Belt Properly
3.16 Vibration
3.17 Operating the Tractor Safely
3.18 Avoid Backover Accidents
3.19 Limited Use in Forestry Operation
3.20 Operating the Loader Tractor Safely
3.21 Keep Riders Off Machine
3.22 Passenger Seat
3.23 Use Safety Lights and Devices
3.24 Towing Trailers/Implements Safely
3.25 Use Caution on Slopes, Uneven Terrain, and Rough Ground
3.26 Freeing a Mired Machine
3.27 Avoid Contact with Agricultural Chemicals
3.28 Handle Agricultural Chemicals Safely
3.29 Handling Batteries Safely
3.30 Avoid Heating Near Pressurized Fluid Lines
3.31 Remove Paint Before Welding or Heating
3.32 Handle Electronic Components and Brackets Safely
3.33 Practice Safe Maintenance
3.34 Avoid Hot Exhaust
3.35 Clean Exhaust Filter Safely
3.36 Work In Ventilated Area
3.37 Support Machine Properly
3.38 Prevent Machine Runaway
3.39 Park Machine Safely
3.40 Transport Tractor Safely
3.41 Service Cooling System Safely
3.42 Service Accumulator Systems Safely
3.43 Service Tires Safely
3.44 Service Front-Wheel Drive Tractor Safely
3.45 Tightening Wheel Retaining Bolts/Nuts
3.46 Avoid High-Pressure Fluids
3.47 Do Not Open High-Pressure Fuel System
3.48 Store Attachments Safely
3.49 Decommissioning ? Proper Recycling and Disposal of Fluids and Components
4 Safety Signs
4.1 Operator’s Manual
4.2 Seat Belt
4.3 Passenger Seat
4.4 Track Accumulators
4.5 Rear Hitch Remote Switch
4.6 Rear SCVs
5 Vehicle Overview
5.1 8RT Series Tractor
6 Operator?s Manual Use
6.1 Operator?s Manual Use
7 General Vehicle Description
7.1 8RT Series Tractor
8 Engine Operation
8.1 Required Machine Stop Warning
8.2 Engine Fuel System and Power Rating
8.3 Battery Disconnect Switch
8.4 Start the Engine
8.5 Theft Deterrent Systems
8.6 Run the Engine
8.7 Stop the Engine
8.8 Restart Engine That Has Run Out of Fuel
8.9 Reduce Fuel Consumption
8.10 Use Battery Booster or Charger
9 Cold Weather Operation
9.1 Cold Weather Starting?Without Starting Aid
9.2 Cold Weather Starting?With Starting Aid
9.3 Change Starting Fluid Canister
9.4 Auxiliary Heaters Use
10 Emissions Equipment
10.1 Exhaust Filter System Overview?Final Tier 4/Stage V Engine
10.2 Aftertreatment Indicators Overview
10.3 Selective Catalytic Reduction (SCR) System Overview
10.4 Auto Exhaust Filter Cleaning Mode?Final Tier 4/Stage V Engine
10.5 Parked Exhaust Filter Cleaning?Final Tier 4/Stage V Engine
10.6 Selective Catalytic Reduction (SCR) System
10.7 Low Fuel or Low DEF Warning
10.8 Disconnect Battery?Final Tier 4/Stage V Engine
10.9 Restored Operation Option
11 Controls and Instruments
11.1 Front Console
11.2 CommandARM? ISOBUS Shortcut Button (ISB)
11.3 Foot Throttle (If Equipped)
12 Corner Post Display
12.1 Corner Post Display
12.2 Information Indicators
12.3 Digital Indicators?Tachometer, Ground Speed, Transmission, and Set Speed
12.4 Gauges – Coolant Temperature, Fuel Level, and DEF Level
13 CommandARM? Controls
13.1 CommandARM? with Generation 4 CommandCenter? Display
13.2 CommandARM? Secondary Brake Lever
13.3 CommandARM? Hitch Controls
13.4 CommandARM? SCV Control Levers
13.5 CommandARM? Climate, Radio and Lighting Controls
13.6 CommandARM? PTO Control Lever
13.7 CommandARM? Left-Hand Side Controls
14 CommandCenter?
14.1 Onscreen Help
14.2 Generation 4 CommandCenter?
14.3 Generation 4 CommandCenter? Processor
14.4 Generation 4 CommandCenter? 4600 Processor Wi-Fi? Capabilities
14.5 Run Page Structure
14.6 Menu
14.7 Machine Settings Overview
14.8 Operating System Applications Overview
14.9 AMS Applications Overview
14.10 CommandCenter? Activations
14.11 Demo Activations
14.12 Automation Status Overview
14.13 Navigate Generation 4 CommandCenter?
14.14 Power Display On and Off
14.15 Navigate Run Pages on Main Page
14.16 Shortcut Buttons
14.17 Display and Sound
14.18 Brightness
14.19 Sound
14.20 Multiple Displays
14.21 Display Calibration
14.22 Date and Time
14.23 Change Current Date
14.24 Change Current Time
14.25 Language and Units
14.26 Language and Units Settings
14.27 Change Pages and Values
14.28 Status Center
14.29 Shortcut Softkeys
14.30 Software Manager
14.31 Factory and Service ADVISOR? Installed Onscreen Help
14.32 Update Display Software
14.33 Activations
14.34 Service ADVISOR? Remote
14.35 Vehicle Reprogramming
14.36 Troubleshooting ? Reprogramming
14.37 System Recovery
14.38 Remote Display Access
14.39 File Manager
14.40 USB Drive
14.41 Capture Screen Shots
14.42 Diagnostics Center
14.43 Controller Diagnostics
14.44 Diagnostic Information
14.45 Hide Diagnostic Center
14.46 Diagnostic Trouble Codes
14.47 Display Hardware
14.48 CAN Bus Information
14.49 CAN Bus Values
14.50 Network
14.51 DataSync
14.52 Users and Access
14.53 User Profiles
14.54 Access Groups
14.55 Layout Manager
14.56 Active Set
14.57 Shortcut Bar
14.58 All Run Pages
14.59 Add, Edit, or Duplicate Run Pages
14.60 Fields and Boundaries
14.61 Field Boundaries
14.62 Manage Clients, Farms, and Fields
14.63 AutoTrac? Guidance
14.64 Equipment Manager
14.65 Machine Profile
14.66 Implement Profile
14.67 Machine Monitor
14.68 Work Monitor
14.69 Work Recording
14.70 Maintenance and Calibrations
14.71 Calibrations
14.72 Radar Calibration
14.73 Slip Calibration
14.74 Service Intervals
14.75 Service Checks
14.76 Steering
14.77 Steering Settings
14.78 Controls Setup
14.79 Settings Manager
14.80 Automation Status
14.81 Read ISOBUS Controller?s Operator?s Manual
14.82 ISOBUS VT
14.83 StarFire? GPS Receiver
14.84 Use Video Display Capability Properly
14.85 Install Video Display Camera
14.86 Video
14.87 Video Triggers
15 Radio Operation
15.1 Radio Faceplate Features
15.2 Declaration of Conformity
15.3 Select Radio Receiver Wave Band
15.4 Set Clock
15.5 Reset Clock
15.6 Turn Confirmation Beep On/Off (BEEP)
15.7 Adjust Maximum Volume at Power-On (ONVOL)
15.8 Program Type (PTY)
15.9 Treble Reduction During Interference (HCUT)
15.10 Set Key Function (KEY PRG)
15.11 Traffic Information
15.12 External Sources
15.13 Select Radio Source with Generation 4 CommandCenter?
15.14 FM, MW, LW Home Page
15.15 Premium Radio USB Home Page
15.16 Premium Radio Bluetooth? Home Page (If Equipped)
15.17 Auxiliary Home Page
15.18 Pair Bluetooth? Device to Generation 4 CommandCenter?
15.19 Manage Paired Bluetooth? Devices
15.20 Phone Operation
15.21 Phone Signal Strength and Battery Charge
15.22 Contact List
15.23 Recent Calls
15.24 Clear Favorites and Call History
16 AMS? Technology
16.1 Machine Sync
16.2 Mount StarFire? Receiver
16.3 Install GreenStar? System Components
16.4 Install Machine Communications Radio (MCR) Antenna (If Equipped)
16.5 Connect AutoTrac? Assisted Steering System
17 Intelligent Total Equipment Control (iTEC?)
17.1 CommandARM? Control Functions
17.2 iTEC? Station Description (2010-52-EU)
17.3 CommandCenter? Pages Descriptions and Functions
17.4 Status Area
17.5 All Sequence Page
17.6 Add New Sequence
17.7 Sequence Step Status
17.8 Edit or Remove Sequence
17.9 Sequence Sets Page
17.10 Perform Sequence
17.11 Recommendations (AutoLearn)
17.12 iTEC Functions?IVT?/AutoPowr? Transmission
17.13 iTEC? Functions?Efficiency Manager? Powershift Transmission
18 Tractor-Implement Automation? (TIA?)
18.1 Tractor-Implement Automation? (TIA?)
18.2 Activate Tractor-Implement Automation? Equipment
18.3 Tractor-Implement Automation? ? Status Page
18.4 Operate Tractor-Implement Automation?
18.5 PTO Requirements
18.6 SCV Requirements
18.7 IVT?/AutoPowr? Requirements
18.8 Powershift Transmission Requirements
18.9 AutoTrac? Guidance Requirements
18.10 Rear Hitch Requirements
18.11 Drive Strategy Requirements
19 Drivetrain
19.1 Drivetrain Overview
20 Brakes
20.1 Brake Use
20.2 Use Secondary Brake Lever
20.3 Brake Warning Indicators
20.4 Hydraulic Trailer Brakes
20.5 Trailer Brake Settings
20.6 Use AutoClutch (If Equipped)
21 Transmission – General Information
21.1 Warm-Up Transmission-Hydraulic System
21.2 Foot Pedal Mode (If Equipped)
21.3 Activate and Set Maximum Set Speed
21.4 Use Maximum Set Speed with Different Transmission Modes
21.5 Intelligent Power Management
21.6 Backup Alarm
21.7 Come Home Mode
22 e23? Transmission
22.1 Operate e23? Transmission with Right-Hand Reverser
22.2 Shift e23? Transmission with Right-Hand Reverser
22.3 Operate e23? Transmission with Left-Hand Reverser
22.4 Shift e23? Transmission with Left-Hand Reverser
22.5 Set Startup Gears
22.6 Stop and Park Tractor
22.7 CommandCenter? Transmission Main Page
22.8 Efficiency Manager? on the e23? Transmission
22.9 Efficiency Manager? on e23? Transmission in Manual Mode
22.10 e23? Custom Mode Settings
23 IVT?/AutoPowr? Transmission
23.1 Controls Identification
23.2 Left-hand and Right-hand Reverser Shift Patterns
23.3 Operate the Transmission
23.4 Adjust Set Speeds
23.5 Set Speeds?Guidelines and Examples
23.6 IVT?/AutoPowr? Modes and Set Maximum Speed
23.7 IVT?/AutoPowr? Custom Mode Settings
23.8 Adjust Reverse/Forward Set Speed Ratio
23.9 Put Tractor in Motion
23.10 Use Creeper Mode
23.11 Stop and Park Tractor
23.12 Downhill Operation in Slippery Conditions
24 PTO, Hitch, and Drawbar
24.1 Attaching PTO-Driven Implement
24.2 Hitch, SCV and PTO External Switches
25 Rear PTO
25.1 Operating Instructions (2010-52-EU)
25.2 Using PTO Shield
25.3 Operate PTO
25.4 PTO Engagement Rate
26 Rear Hitch
26.1 Hitch Capacities (2010-52-EU)
26.2 Rear Hitch
26.3 Hitch Control Lever
26.4 Lock and Damping
26.5 Adjust Load/Depth Control (Draft Response)
26.6 Position Control Use
26.7 Draft Control Use
26.8 Adjust Rear Hitch Upper Limit
26.9 Adjust Rear Hitch Drop Rate
26.10 Adjust Rear Hitch Raise Rate
26.11 Adjust Slip Sensitivity
26.12 Float Operation
26.13 Hitch Components
26.14 Rear Hitch Remote Switches
26.15 Hitch Manual Lowering
26.16 Correct Center Link Position
26.17 Using Sway Blocks
26.18 Attach Implement to Quick-Hitch
26.19 Adjusting Implement Level
26.20 Changing Lateral Float
26.21 Detaching Implement from Quick-Hitch
26.22 Hitch Conversion?Convertible Quick-Hitch
26.23 Converting Category 4 Convertible Quick-Hitch Lower Hooks
26.24 Converting Category 3/4 Convertible Quick-Hitch Upper Hook
27 Drawbar
27.1 Drawbar Options and Load Limits
27.2 Adjusting Drawbar Length
27.3 Adjusting Drawbar Height
27.4 Adjusting Drawbar Side-to-Side
27.5 Installing and Using Clevis Assembly
28 Hydraulics – General Information
28.1 Hydraulic System Overview
29 Selective Control Valves
29.1 Configure SCV Modes
29.2 Configure SCV – Standard Mode
29.3 Activate Independent Mode
29.4 Configure SCV – Independent Mode
29.5 Configure SCV – Feature Mode
29.6 Flow Sharing
29.7 Total SCV Flow
29.8 Six Position SCV Control Levers
29.9 SCV Control Lever?Neutral Position
29.10 SCV Control Lever?Extend and Retract Position
29.11 SCV Control Lever?Extend Detent and Retract Detent Position
29.12 SCV Control Lever?Float Position
29.13 Operator Presence Sensor
29.14 Hitch, SCV and PTO External Switches
29.15 CommandARM? Joystick (If Equipped)
29.16 CommandARM? Joystick (If Equipped) – Custom Setup
29.17 CommandARM? Joystick (If Equipped) – Layout and Joystick Lever Functions
29.18 SCV and Joystick Flow Response Setting
30 Hydraulic Connections
30.1 Connect Rear Hydraulic Hoses
30.2 Disconnect Rear Hydraulic Hoses
30.3 Hydraulic Component Identification
30.4 Using Load-Sensing Hydraulic System?Power-Beyond
30.5 Examples Using Load-Sensing Hydraulic System?Power-Beyond
30.6 Using Hydraulic Spray Pumps
30.7 Implement Connection, Example 1?Pressure Control Valve Applications (Grain Drills or Air Seeders with Constant Down-Pressure System)
30.8 Implement Connection, Example 2?Motor Application Using Motor Case Drain
30.9 Implement Connection, Example 3?Motor Application Using SCV Retract and Auxiliary Motor Return
30.10 Implement Connection, Example 4?Planter with Vacuum Motor and Return Line to SCV Using Motor Return Tip
30.11 Implement Connection, Example 5?Planter with Vacuum Motor, Return Line to Motor Return and Lift Assist
30.12 Implement Connection, Example 6?Planter with Vacuum Motor and Return Line to Motor Return
30.13 Using Hydraulic Motor Return
30.14 Using Hydraulic Motor Case Drain
30.15 Using Implements Requiring Large Volumes of Oil
31 TouchSet? Depth Control
31.1 Attaching Implement and Control System
31.2 Reset Implement Connector
31.3 Set TouchSet? Depth Controls
31.4 Use TouchSet? Depth Controls
32 Laser Scraper Control
32.1 Laser Scraper?for Scrapers Equipped with Scraper Control Unit
33 Tracks – General Information
33.1 General Track Use Guidelines
33.2 Tracks Service
34 Operator?s Station – General Information
34.1 Cab Classification According to EN 15695-1 (for Application of Crop Protection Chemicals and Liquid Fertilizer) (2010/52/EU)
34.2 Avoid Contact with Agricultural Chemicals
34.3 Clean Vehicle of Hazardous Pesticides
34.4 Keep Riders Off Machine
34.5 Keep Operator Station Window and Door Closed
34.6 Use Seat Belts
34.7 Use Emergency Exit
34.8 Monitor Bracket Mounts
35 Seat
35.1 Adjust ComfortCommand? Seat
35.2 Adjust Heated Leather Seat
35.3 Adjust CommandARM? Position
35.4 Operator Presence Sensor (If Equipped)
35.5 Use Passenger Seat
36 Steering Column
36.1 Adjust Steering Wheel and Column
36.2 Operate Horn
37 Mirrors
37.1 Manual Mirror
37.2 Electric Mirror
37.3 Telescoping Heated Electric Mirror
38 Wiper Washer
38.1 Operate Front Wiper and Washer
38.2 Operate Rear Wiper and Washer
38.3 Operate Right-Hand Wiper and Washer
39 Lights
39.1 Light Identification
39.2 Configurable Lights
39.3 Steering Column Light Controls
39.4 Exit Lights
39.5 Operate Turn Signals and High/Low Beam
39.6 Safety Lights and Devices
39.7 CommandARM? Light Buttons
39.8 Hazard Lights and Extremity Warning Lights
39.9 Rotary Beacon Light
39.10 7-Pin Outlet
40 Accessories
40.1 Pull-Down Sunshade
40.2 Install Business Band or Citizens Band (CB) Radio and Antenna
40.3 Auxiliary Power Strip Use
40.4 Accessory Electrical Outlet Use
40.5 Connect Compatible Electronic Equipment
40.6 Configure Tractor for GPS or Radar
40.7 Refrigerator or Storage Space
41 HVAC
41.1 Climate Controls
41.2 HVAC Settings?Generation 4 CommandCenter?
42 Performance Ballasting
42.1 General Ballasting Information
42.2 Select Ballast (2010-52-EU)
42.3 Calculate Maximum Permissible Download on Trailer Hitch (2010-52-EU)
42.4 Measure Track Slip
42.5 Determine Ballasted Tractor Weight, Weight Split, and Axle Loads
42.6 Ballast Types
42.7 Mounted Spray Tank Use
42.8 Implement Guidelines
43 Transport
43.1 Driving Tractor on Roads
43.2 Transporting
43.3 Towed Mass (2010-52-EU)
43.4 Towing Loads
43.5 Tow Points
43.6 Tow Mode
43.7 Towing Tractor
43.8 Emergency Brake Steering
43.9 Freeing a Mired Machine
43.10 Carrier Transport
44 Fuel, Lubricants, and Coolants – General Information
44.1 Determine Tractor Engine Type
44.2 Minimizing the Effect of Cold Weather on Diesel Engines
44.3 Oil Filters
45 Fuel
45.1 Diesel Fuel
45.2 Supplemental Diesel Fuel Additives
45.3 Biodiesel Fuel
45.4 Lubricity of Diesel Fuel
45.5 Handling and Storing Diesel Fuel
45.6 Avoid Static Electricity Risk When Refueling
45.7 Fill Fuel Tank
45.8 Testing Diesel Fuel
45.9 Fuel Filters
46 Diesel Exhaust Fluid (DEF)
46.1 Diesel Exhaust Fluid (DEF) ? Use in Selective Catalytic Reduction (SCR) Equipped Engines
46.2 Storing Diesel Exhaust Fluid (DEF)
46.3 Refilling Diesel Exhaust Fluid (DEF) Tank
46.4 Testing Diesel Exhaust Fluid (DEF)
47 Engine Oil
47.1 Diesel Engine Oil Service Interval for Operation at High Altitude
47.2 John Deere Break-In Plus? Engine Oil ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
47.3 Diesel Engine Oil ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
47.4 Engine Oil and Filter Service Intervals ? Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V Engines
48 Engine Coolant
48.1 Diesel Engine Coolant (engine with wet sleeve cylinder liners)
48.2 Operating in Warm Temperature Climates
48.3 Water Quality for Mixing with Coolant Concentrate
48.4 Testing Coolant Freeze Point
48.5 Disposing of Coolant
49 Other Lubricants
49.1 Mixing of Lubricants
49.2 Alternative and Synthetic Lubricants
49.3 Lubricant Storage
49.4 Transmission and Hydraulic Oil
49.5 Mid-Frame Roller Oil
49.6 Gear Oil
49.7 Multipurpose Extreme Pressure (EP) Grease
49.8 Corn Head Grease
50 Service – General Information
50.1 Service Sections Overview
50.2 Service Tasks Performed As Required
50.3 Identify Tractor Engine Emissions Status
50.4 Open Hood
50.5 Diesel Particulate Filter Service
50.6 Jack Up Tractor – Lifting Points and Support Stand Placement (2010-52-EU)
50.7 Service and Connect STC? (Snap-to-Connect) Fittings
50.8 High-Pressure Washer Use
50.9 Do Not Modify Fuel System
50.10 Do Not Open High-Pressure Fuel System
50.11 Bleed Fuel System
50.12 Identify Zinc-Flake Coated Fasteners
50.13 Unified Inch Bolt and Screw Torque Values
50.14 Metric Bolt and Screw Torque Values
51 Service – Break In (100 Hours or Less)
51.1 Perform Break-In Services
51.2 Perform Track Systems Break-In
52 Service – Record Charts
52.1 Engine Oil and Filter Change
52.2 As Required Service
52.3 Annual Service
52.4 10 Hour or Daily Service
52.5 50 Hour Service
52.6 250 Hour Service
52.7 500 Hour Service
52.8 750 Hour Service
52.9 1000 Hour Service
52.10 1250 Hour Service
52.11 1500 Hour Service
52.12 1750 Hour Service
52.13 2000 Hour Service
52.14 2250 Hour Service
52.15 2500 Hour Service
52.16 2750 Hour Service
52.17 3000 Hour Service
52.18 3250 Hour Service
52.19 3500 Hour Service
52.20 3750 Hour Service
52.21 4000 Hour Service
52.22 4250 Hour Service
52.23 4500 Hour Service
52.24 4750 Hour Service
52.25 5000 Hour Service
52.26 5250 Hour Service
52.27 5500 Hour Service
52.28 5750 Hour Service
52.29 6000 Hour Service
52.30 Services Beyond 6000 Hours
53 Service – Clean
53.1 Diesel Particulate Filter (DPF)?Final Tier 4/Stage V Engine
53.2 Exhaust Filter/Diesel Particulate Filter (DPF) Ash Handling and Disposal
53.3 Exhaust Filter Disposal
53.4 Engine Cooling System
53.5 Access DEF Tank Drain Plug
53.6 Cleaning Diesel Exhaust Fluid (DEF) Tank
53.7 Clean Display
53.8 Dual Beam Radar Sensor
53.9 Optional Fuel Water Separator
53.10 Optional Fuel Water Separator Filter Element
53.11 Suspension Compressor Filter, Compressor, and Air Bag
53.12 Hydraulic Oil Suction Screen
54 Service – Check
54.1 Engine and Exhaust Compartments
54.2 Air Conditioning System
54.3 Engine Water Pump Weep Hole – Final Tier 4/Stage V Engine
54.4 Vari-Cool? Fan Drive and Belt?Final Tier 4/Stage V Engine
54.5 Fuel Tank Sump
54.6 Hydraulic Trailer Brakes
54.7 Engine Oil Level
54.8 Transmission-Hydraulic Oil Level
54.9 NEUTRAL Start System
54.10 Cab Suspension Components
54.11 Transmission PARK System
54.12 Engine Air Intake System
54.13 Seat Belts
54.14 Engine Coolant Level
54.15 Track Tension
54.16 Tread Settings
54.17 Track Adjustment
54.18 Align Track
54.19 Walking Beam Bumper Stops
54.20 Engine Coolant Freeze Point
54.21 Auxiliary Drive Belt and Drive Belt Tensioner
54.22 Drive Wheel Hub Housing Oil Level
54.23 Mid-Rollers Oil Level
54.24 Idler Wheel Hub Oil Level
54.25 Mid-Rollers, Drive, and Idler Wheels
54.26 Track Wear and Trash Build-Up
54.27 Secondary Brake
54.28 Walking Beam Air Suspension System
54.29 Drive Wheel And Walking Beam Settings?Narrow Tread
54.30 Drive Wheel And Walking Beam Settings?Standard and Wide Tread
54.31 Water Separator
54.32 Engine Valve Clearance
55 Service – Tighten
55.1 Drive Wheel, Drive Wheel Sleeve, Wedges, Idler, and Mid-Roller Cap Screws
56 Service – Change
56.1 Engine Oil and Filter
56.2 Cab Classification According to EN 15695-1 (for Application of Crop Protection Chemicals and Liquid Fertilizer) (2010/52/EU)
56.3 Cab Recirculation Air Filter
56.4 Cab Fresh Air Filter
56.5 Engine Primary and Secondary Air Filters
56.6 Transmission-Hydraulic Oil and Filters
56.7 Fuel Tank Vent Filter
56.8 SCV Pilot Valve Filter
56.9 DEF Tank Vent Filter?Final Tier 4/Stage V Engine
56.10 In-Line DEF Filter (If Equipped)
56.11 DEF Header Filter?Final Tier 4/Stage V Engine
56.12 Access DEF Dosing Unit Filter
56.13 DEF Dosing Unit Filter?Final Tier 4/Stage V Engine
56.14 Engine Coolant
56.15 Vari-Cool? Fan Belt – 9.0L Final Tier 4/Stage V Engines
56.16 Vari-Cool? Fan Drive Bushings, Seals, and Wear Pads
56.17 Auxiliary Drive Belt
56.18 Fuel Filters
56.19 Walking Beam Bumper Stops
56.20 Front Suspension Air Compressor Inlet Filter
56.21 Steering Filter
56.22 Transmission Torsional Damper
56.23 Differential Oil
56.24 IVT?/AutoPowr? and e23?Transmissions-Hydraulic Oil
56.25 Remove and Install Track
57 Service – Lubricate
57.1 Rear Hitch
57.2 Draft Link Support Shaft Bushing
57.3 Vari-Cool? Fan Drive?Final Tier 4/Stage V Engine
57.4 Track Tension Cylinders
58 Service – Electrical
58.1 Service – Electrical Overview
58.2 Welding Near Electronic Control Units
58.3 Keep Electronic Control Unit Connectors Clean
58.4 Compressed Air Use
58.5 High-Pressure Washers Use
58.6 Disconnect Battery
58.7 Handling Batteries Safely
58.8 Service Batteries and Connectors
58.9 Access Load Center Fuses
58.10 Access Master Fuses
58.11 Access Implement Power Relay Module Fuses
58.12 Handle Halogen Light Bulbs Safely
58.13 Change Front HID/LED Light Assembly
58.14 Change Front Grille Halogen Light Bulbs
58.15 Adjust Front Grille Lights
58.16 Adjust Headlights
58.17 Change Front, Side And Rear Cab Roof Light Bulb
58.18 Change Brake or Turn Signal Light Bulb
58.19 Change Dome Light Bulb
58.20 Change Extremity Warning Light Bulb
59 Troubleshooting – Procedures
59.1 Engine
59.2 Transmission
59.3 Hydraulic System
59.4 Hitch
59.5 Selective Control Valve (SCV)
59.6 TouchSet? Depth Control
59.7 Electrical System
59.8 Operator Enclosure
59.9 Steering System
59.10 Premium Radio
60 Troubleshooting – Diagnostic Trouble Codes (DTC)
60.1 STOP and Service Alert Indicators
60.2 Information Indicator
60.3 Access Diagnostic Trouble Codes
61 Service – Storage
61.1 Place Tractor in Storage
61.2 Remove Tractor from Storage
61.3 Paint Finish Care
62 Specifications
62.1 Engine
62.2 Capacities
62.3 Fluorinated Greenhouse Gas
62.4 Hydraulic System
62.5 Transmission and Power Train
62.6 Hitch, Drawbar, and PTO
62.7 Electrical System
62.8 Other Equipment
62.9 Overall Dimensions
62.10 Loads and Weights (2010-52-EU)
62.11 How to Calculate Permissible Mass (2010-52-EU)
62.12 Sound Level (2010-52-EU)
62.13 Ground Speeds – e23? Transmission
62.14 Ground Speeds – IVT?/AutoPowr? Transmission
62.15 Required Emission-Related Information
62.16 Carbon Dioxide Emissions (CO?)
63 Identification Numbers
63.1 Identification Plates
63.2 Product Identification Number
63.3 Engine Serial Number
63.4 Cab Serial Number
63.5 Transmission Serial Number
63.6 Track Serial Numbers
63.7 Keep Proof of Ownership
63.8 Keep Machines Secure
64 Change of Ownership
64.1 Subsequent Ownership
65 Predelivery
65.1 Predelivery Checklist
65.2 Delivery Checklist and Certificate
66 John Deere Service Literature Available
66.1 Technical Information
67 John Deere Service Keeps You On The Job
67.1 John Deere Parts
67.2 The Right Tools
67.3 Well-Trained Technicians
67.4 Prompt Service