John Deere 8100 – 8600 Self-Propelled Forage Harvester Operator Manual OMDXE12645

Table of Content:

1 Introduction
1.1 Foreword
1.2 Emissions Performance and Tampering
1.3 Trademarks
1.4 A Message to Our Customers
1.5 John Deere Technical Information Bookstore
1.6 Download Instructions
2 Safety
2.1 Recognize Safety Information
2.2 Follow Safety Instructions
2.3 Understand Signal Words
2.4 Observe Road Traffic Regulations
2.5 Parking and Leaving the Machine
2.6 Prevent Machine Runaway
2.7 Use Safety Lights and Devices
2.8 Prepare for Emergencies
2.9 Wear Protective Clothing
2.10 Handle Agricultural Chemicals Safely
2.11 Handle Fuel Safely?Avoid Fires
2.12 Store Attachments Safely
2.13 Check Machine Safety
2.14 Use Steps and Handholds Correctly
2.15 Handle Electronic Components and Brackets Safely
2.16 Use Electronic Display Properly
2.17 Operate Guidance Systems Safely
2.18 Read the Guidance Manual
2.19 Cutterhead Access Foot Step
2.20 Engine Compartment Access Ladder
2.21 Keep Riders and Children off Machine
2.22 Instructional Seat
2.23 Use Seat Belts
2.24 Road Safety Mode Button
2.25 Drive the Machine
2.26 Avoid Backover Accidents
2.27 Guards and Shields
2.28 Handle Knives
2.29 Stay Clear of Harvesting Units
2.30 Keep Hands Away From Knives
2.31 Stay Clear of Rotating Drivelines
2.32 Avoid Entanglement
2.33 Transport With Header Installed
2.34 Emergency Exit
2.35 Radio Aerial
2.36 Work In Ventilated Area
2.37 Avoid Hot Exhaust
2.38 Clean Exhaust Filter Safely
2.39 Avoid Static Electricity Risk When Refueling
2.40 Practice Safe Maintenance
2.41 Service Machines Safely
2.42 Support Machine Properly
2.43 Service Accumulator Systems Safely
2.44 Avoid High-Pressure Fluids
2.45 Prevent Battery Explosions
2.46 Prevent Acid Burns
2.47 Follow Tire Recommendations
2.48 Retorque Wheel Bolts and Nuts
2.49 Service Tires Safely
2.50 Service Cooling System Safely
2.51 Speed Limit
2.52 Decommissioning ? Proper Recycling and Disposal of Fluids and Components
2.53 Avoid High-Pressure Jet on Safety Decals
2.54 Machine Safety Features
2.55 Safety Decals
2.56 Quick Response (QR) Code
2.57 Remove Accumulated Crop Debris
2.58 Cleaning and Inspection – Instructions
2.59 Fire Extinguisher Recommendations
2.60 Fire Prevention – Instructions
2.61 Operate a Fire Extinguisher
2.62 In Case of Fire
2.63 Automatic Guidance System Detected
2.64 Use Electronic Display Properly
2.65 Prevent Electrical Shock and Fires
2.66 Avoid Exposure to High Radio Frequency Fields
3 Operating the Controls and Displays
3.1 Generation 4 Display
3.2 Cab Access
3.3 Cab Doors
3.4 Emergency Exit Cab Hammer
3.5 Steering Column
3.6 Windshield Wiper/Washer Selector Switch
3.7 ComfortCommand? Operator’s Seat (Premium Cloth Seat)
3.8 ComfortCommand? Operator’s Seat (Premium Leather Seat)
3.9 Left-Hand Armrest and Seat Back (Premium Cloth/Leather Seat)
3.10 Heated/Ventilated Seat Switch (Premium Cloth/Leather Seat)
3.11 Lumbar Support Switch (Premium Leather Seat)
3.12 Instructional Seat
3.13 Seat Belts
3.14 CommandTouch? Armrest and CommandARM? Control Consoles
3.15 CommandCenter? Display
3.16 Overhead Control Panel
3.17 Rear-View Mirror and Outside Mirrors
3.18 Cab Roof
3.19 Brake Pedals
3.20 Cab Interior Lights
3.21 Power Outlet Socket Strip
3.22 Cab 12-V Sockets
3.23 GreenStar? 4640 Display and Video Signal Socket
3.24 Images Collected From Camera Devices
3.25 Service ADVISOR? Diagnostic Socket
3.26 USB Port
3.27 Refrigerator (If Equipped)
3.28 Storage Locations
3.29 CommandTouch? Armrest Console
3.30 Road Safety Mode Button
3.31 Engine Speed Buttons
3.32 Main Clutch Switch
3.33 Gear Buttons (PBST Machines Only)
3.34 Park Brake Button
3.35 Differential Lock Button (ProDrive? Machines Only)
3.36 Four-Wheel Drive Button
3.37 Traction Control Button (ProDrive? Transmission Only)
3.38 Left, Right, and Rear Wiper Buttons (If Equipped)
3.39 Air Compressor Button (If Equipped)
3.40 Row Guidance Offset Control Dial (If Equipped)
3.41 Header Height/Ground Pressure Control Dial
3.42 ProTouch Functions Button (If Equipped)
3.43 CommandARM? Controls
3.44 Menu Button
3.45 Home Button
3.46 Header Settings Button
3.47 Cutterhead Assembly Settings Button
3.48 Additive Dosing System Settings Button (If Equipped)
3.49 Spout Settings Button
3.50 Engine Settings Button
3.51 Vehicle Settings Button
3.52 Operator Settings Button
3.53 Statistics Button
3.54 ClimaTrak? Automatic Temperature Control
3.55 Radio Controls (If Equipped)
3.56 Machine Lights (Depending on Machine Equipment)
3.57 Machine Hydraulic Functions
3.58 Spout Raise/Lower Switch
3.59 SCV I Switch
3.60 SCV II Switch
3.61 Wagon Dump Switch (If Equipped)
3.62 CommandCenter? Display
3.63 CommandCenter? Display Navigation
3.64 CommandCenter? Display Startup Sequence
3.65 CommandCenter? Display Functions Icons
3.66 Corner Post Display
3.67 GreenStar? 4640 Display
3.68 Multi-Function Lever
3.69 Quick Stop Button
3.70 Header Engage/Reverse Switch
3.71 Activation Buttons
3.72 Header Raise/Lower Switch
3.73 Header Tilt Switch (With AHC Option Only)
3.74 Spout Turn Switch
3.75 Spout Flap Raise/Lower Switch
3.76 Spout Return to Home Position Button (If Equipped with Automatic Spout Control Option)
3.77 Active Fill Control Button (If Equipped with Active Fill Control Option)
3.78 AutoTrac? Button
3.79 Configurable Switches
3.80 Configurable Switch R?T (Assigned to SCV I)
3.81 Configurable Switch P (Assigned to Horn)
3.82 Configurable Switch M?N (Assigned to Spout Raise/Lower)
3.83 Configurable Switch K?L (Assigned to SCV II)
3.84 Message Center Page
3.85 Display Main Page
3.86 Display Advanced Settings Page
3.87 Layout Manager Page
3.88 Access Manager Page
3.89 Home Page
3.90 Header Page
3.91 Header Drive Speed Control?Auto Mode
3.92 Header Drive Speed Control?Manual Mode
3.93 Header Setup Page
3.94 Header Advanced Settings Page
3.95 Selective Control Valve (SCV) and StalkBuster? Maintenance Mode (If Equipped) Tab
3.96 Automatic Header Control
3.97 Header Height Resume (Return to Position) – Operation
3.98 Active Header Float (Return to Pressure) – Operation
3.99 Header Height Sensing (Machines with AHC Option Only) – Operation
3.100 Cutterhead Assembly Setup Page
3.101 Cutterhead Assembly Advanced Settings Tab (1)
3.102 Stone/Metal Detector and Kernel Processor Settings Tab (2)
3.103 XStream KP? Kernel Processor Bearing Temperatures Tab (3)
3.104 Knife Sharpening/Stationary Knife Adjustment
3.105 AutoLoc? Page
3.106 Metal/Stone Detector Operation
3.107 Additive Dosing System Page (Option)
3.108 Additive Dosing System Page?High Volume (Option)
3.109 Additive Dosing System Page?High and Low Volume (Option)
3.110 Additive Dosing System?Water Injection Bar
3.111 Operate High and Low Volume Dosing System with Water Injection Bar
3.112 Operate Water Injection Bar
3.113 Spout Speeds Page
3.114 Spout Setup Page
3.115 Auto Spout Positioning Page
3.116 Spout Fold/Unfold Timeout
3.117 Automatic Spout Control (Option)
3.118 Store and Assign Spout Position
3.119 Active Fill Control (Option)
3.120 Aftertreatment Indicators Overview
3.121 Required Machine Stop Warning
3.122 Engine Page
3.123 Engine Speed Management?Field Mode (ProDrive? Machines Only)
3.124 Engine Speed Management?Field Mode (PBST Machines Only)
3.125 Engine Speed Limit
3.126 Exhaust Filter Cleaning?Final Tier 4/Stage V Engines Only
3.127 Engine Settings Page
3.128 Vehicle Settings Page
3.129 Vehicle Lubrication
3.130 Header Lubrication
3.131 Tow Mode Page
3.132 Wiper Interval Page
3.133 Mass Flow Calibration
3.134 Diagnostics Information
3.135 Spout Fold Hydraulic Pressure Relief Function
3.136 Rear Axle Force Adjustment (PBST Machines Only)
3.137 Lighting Setup Page
3.138 Machine Lighting
3.139 Machine Lighting?Lower Front Location
3.140 Machine Lighting?Upper Front Location
3.141 Machine Lighting?Rear and Side Location
3.142 Operator Settings Page
3.143 Programmable Switch Function Assignment
3.144 ProTouch Page
3.145 ProTouch?Field Transition Status Page
3.146 ProTouch?Road Transition Status Page
3.147 Harvest Statistics Page
3.148 Machine Performances Page
3.149 Statistics Settings Page
3.150 Diagnostic Trouble Code Priorities
3.151 Access Diagnostic Trouble Codes Menu
3.152 AutoTrac? RowSense? Guidance (Option)
3.153 GreenStar? Settings Page
3.154 GreenStar? Guidance Page
3.155 GreenStar? Machine/Implement Pages
3.156 Enable/Activate/Operate AutoTrac? RowSense?
3.157 Calibrate the Row Sensor
3.158 Video Interface (Option)
3.159 Video Trigger Setup Page
3.160 Phone Interface (Option)
3.161 Audio Interface (Option)
3.162 Acoustic Alarm System
4 Field Operation
4.1 General
4.2 Quick Response (QR) Code
4.3 Selective Catalytic Reduction (SCR) System Overview
4.4 Prestarting Checks
4.5 Break in the Engine
4.6 Operate the Engine
4.7 Handle Starting Fluid Safely
4.8 Start the Engine With a Battery Booster or Charger
4.9 Disconnect the Battery on Machine with Final Tier 4/Stage V Engine
4.10 Battery Disconnect Switch
4.11 Operate the Exhaust Cleaning System
4.12 Transport Information
4.13 Tow the Machine
4.14 Ballast the Machine
4.15 Attach Weight Plates
4.16 Lateral Tilt Frame Locking Device (Machine without Lateral Tilt Float Option Only)
4.17 Machine Road Transport Guard (Germany and Italy Only)
4.18 Machine Road Transport Deflectors
4.19 Attach and Detach Header
4.20 Basic Settings of Machine
4.21 Operate Machine in Grass or Alfalfa Harvest
4.22 Operate Machine in Corn (Maize) Harvest
4.23 Operate Machine in Ear Corn Silage
4.24 Operate Machine in Whole Plant Silage
4.25 Operate Machine in Sorghum (Milo) Harvest
4.26 Operate the Air Compressor System (Option)
4.27 Operate the Grass Chute
4.28 Operate a 460plus StalkBuster? Header
4.29 Operate the Kernel Processor (Option)
4.30 Remove Kernel Processor
4.31 Install Kernel Processor
4.32 Adjust Premium KP? Kernel Processor Gap (Manual Adjustment)
4.33 Adjust XStream KP? Kernel Processor Gap (Manual Adjustment)
4.34 XStream KP? Kernel Processor Lubrication System Air Supply (If Equipped)
4.35 Adjust Lateral Tilt Frame Balance Springs
4.36 Open/Close Discharge Chute
4.37 Adjust Spiral/Recutter Floor
4.38 Adjust Smooth Roll Scraper
4.39 Adjust Feed Roll Springs
4.40 Adjust Feed Roll Bars
4.41 Cutterhead Knives
4.42 Stationary Knife
4.43 Kernel Processor Rolls
4.44 Feed Roll Paddles
4.45 Grass and Whole-Crop Machine Adaptation
4.46 Spiral Upper Front Feed Roll Option
4.47 Ear Corn Silage Machine Adaptation
4.48 Grain Panels (Corn)
4.49 Feed Roll Stone Deflector
4.50 Transfer Stereo Camera from Machine-to-Machine (If Equipped)
5 Lubrication and Maintenance
5.1 Required Emission-Related Information
5.2 Quick Response (QR) Code
5.3 General Maintenance Guidelines
5.4 Cutterhead Access Foot Step
5.5 Engine Compartment Access Ladder
5.6 Central Service Compartment Access
5.7 Tool Box Compartment
5.8 Service Lights (If Equipped)
5.9 12 V Power Outlets
5.10 Secure Cutterhead Lift Lock
5.11 Interactive Calibration Procedures
5.12 Break-in Service
5.13 After the First 10 Operating Hours
5.14 During the First 50 Operating Hours
5.15 After the First 100 Operating Hours
5.16 John Deere Break-In? Plus Engine Oil (8100?8600 Final Tier 4/Stage V Engine Only)
5.17 John Deere Break-In? Engine Oil (8100?8600 Tier 3/Stage III A Engine Only)
5.18 John Deere Break-In? Engine Oil (8100?8600 Tier 2/Stage II Engine Only)
5.19 Diesel Engine Oil (8100?8600 Final Tier 4/Stage V Engine Only)
5.20 Diesel Engine Oil (8100?8600 Tier 3/Stage III A Engine Only)
5.21 Diesel Engine Oil (8100?8600 Tier 2/Stage II Engine Only)
5.22 Engine Oil and Filter Service Intervals (8100?8600 Final Tier 4/Stage V Engine Only)
5.23 Engine Oil and Filter Service Intervals (8100?8600 Tier 3/Stage III A Engine Only)
5.24 Engine Oil and Filter Service Intervals (8100?8600 Tier 2/Stage II Engine Only)
5.25 Transmission Oil
5.26 Hydraulic Oil
5.27 XStream KP? Kernel Processor Lubrication System Oil
5.28 Multipurpose Extreme Pressure Grease
5.29 General Multipurpose Grease
5.30 Grease for Automated Lubrication Systems
5.31 Brake Fluid (Push-Button Shift Transmission Only)
5.32 Capacities
5.33 Important Lubrication Instructions
5.34 Central Lubrication System
5.35 Refill/Bleed Central Lubrication System Reservoir
5.36 XStream KP? Kernel Processor Lubrication System Reservoir (If Equipped)
5.37 Greasing Points (Manually Lubricated)
5.38 Every 10 Operating Hours
5.39 Every 50 Operating Hours
5.40 Every 100 Operating Hours
5.41 Every 250 Operating Hours
5.42 Every 500 Operating Hours
5.43 Every 1000 Operating Hours
5.44 Every 1500 Operating Hours
5.45 Every 2000 Operating Hours
5.46 Every 2500 Operating Hours (8200?8600)
5.47 As Required
5.48 Annually
5.49 Every 2 Years
5.50 Every 3 Years
5.51 Every 3 Years or 4500 Operating Hours
5.52 Every 6 Years or 6000 Operating Hours
5.53 Hydraulic Hose Replacement
5.54 Hydraulic System Cleanliness
5.55 Change Hydraulic System Oil
5.56 Replace Hydraulic System Reservoir Filter
5.57 Change Power Distribution Gear Case Oil
5.58 Replace Power Distribution Gear Case Oil Filter
5.59 Change ProDrive? Transmission Oil
5.60 Replace ProDrive? Transmission Hydraulic Oil Filter
5.61 Change Push-Button Shift Transmission Oil
5.62 Change Final Drive Oil
5.63 Change Header Gear Case Oil
5.64 Change Left Feed Roll Gear Case Oil
5.65 Change Right Feed Roll Gear Case Oil
5.66 Change Rear Axle Oil
5.67 Diesel Exhaust Fluid (DEF) ? Use in Selective Catalytic Reduction (SCR) Equipped Engines
5.68 Storing Diesel Exhaust Fluid (DEF)
5.69 Testing Diesel Exhaust Fluid (DEF)
5.70 Disposal of Diesel Exhaust Fluid (DEF)
5.71 Fill the Diesel Exhaust Fluid (DEF) Tank
5.72 Diesel Fuel
5.73 Handling and Storing Diesel Fuel
5.74 Lubricity of Diesel Fuel
5.75 Testing Diesel Fuel
5.76 Biodiesel Fuel
5.77 Fill the Fuel Tank
5.78 Minimizing the Effect of Cold Weather on Diesel Engines
5.79 Mixing of Lubricants
5.80 Oilscan? and CoolScan?
5.81 Alternative and Synthetic Lubricants
5.82 Lubricant Storage
5.83 Oil Filters
5.84 Diesel Engine Coolant (engine with wet sleeve cylinder liners)
5.85 Supplemental Coolant Additives
5.86 Drain Intervals for Diesel Engine Coolant
5.87 Additional Information About Diesel Engine Coolants and John Deere LIQUID COOLANT CONDITIONER
5.88 Testing Diesel Engine Coolant
5.89 Operating in Warm Temperature Climates
5.90 Adjust Engine Valve Clearance
5.91 Check Engine Oil Level
5.92 Change Engine Oil and Filter (8100 Final Tier 4/Stage V and Tier 3/Stage III A Engine Only)
5.93 Change Engine Oil and Filter (8100 Tier 2/Stage II Engine Only)
5.94 Change Engine Oil and Filter (8200?8600 Final Tier 4/Stage V Engine Only)
5.95 Change Engine Oil and Filter (8200?8600 Tier 2/Stage II and Tier 3/Stage III A Engine Only)
5.96 Check Engine Coolant Pump Weep Hole
5.97 Do Not Open High-Pressure Fuel System
5.98 Do Not Modify Fuel System
5.99 Fuel Tank Breather
5.100 Drain Water Separator
5.101 Drain Fuel Precleaner (8100?8600 Tier 2/Stage II Engine Only)
5.102 Replace Fuel Filter Elements (8100?8600 Final Tier 4/Stage V and Tier 3/Stage III A Engine Only)
5.103 Replace Fuel Filter Elements (8100 Tier 2/Stage II Engine Only)
5.104 Replace Fuel Filter Elements (8200?8600 Tier 2/Stage II Engine Only)
5.105 Check Fuel Injection Nozzles
5.106 Check Cooling Elements
5.107 Check the Rotary Screen
5.108 Engine Coolant
5.109 Engine Coolant Drain Valves
5.110 Drain, Flush, and Refill Cooling System
5.111 Check Alternator/Compressor and Air Compressor Drive Belt Wear
5.112 Check Fan Drive Belt Wear
5.113 Check Suction Fan Drive Belt Wear
5.114 Air Cleaner Elements
5.115 Air Intake Lines
5.116 Turbocharger
5.117 Diesel Particulate Filter Maintenance and Service
5.118 Exhaust Filter/Diesel Particulate Filter Ash Handling and Disposal
5.119 Exhaust Filter Disposal
5.120 Clean Diesel Exhaust Fluid (DEF) Tank
5.121 Clean Diesel Exhaust Fluid (DEF) Tank Filler Neck Filter
5.122 Replace Diesel Exhaust Fluid (DEF) Pump Filter and Equalizing Element
5.123 Replace Diesel Exhaust Fluid (DEF) Tank Vent Filter
5.124 Replace Diesel Exhaust Fluid (DEF) In-Line Filter
5.125 Open/Close Feed Roll Housing
5.126 Cutterhead Knives?General
5.127 Replace Cutterhead Knives
5.128 Replace Individual Knives
5.129 Replace Complete Set of Knives
5.130 Stationary Knife?General
5.131 Replace Stationary Knife
5.132 Knife Sharpening Device?General
5.133 Replace Sharpening Stone
5.134 Replace Spiral/Recutter Floor
5.135 Replace Recutter Floor Knives
5.136 Replace Feed Roll Stone Deflector
5.137 Replace Cutterhead Wear Plate
5.138 Replace Feed Roll Housing Wear Plate
5.139 Weld Near Electronic Control Units
5.140 Keep Electronic Control Unit Connectors Clean
5.141 Observe Electrical Precautions
5.142 Basic Electrical Component Handling – Precautions for Machines Equipped with Computer Controlled Systems
5.143 Battery Disconnect Switch
5.144 Fuse Center
5.145 Inline Fuses
5.146 Master Fuses
5.147 Cab Fuse (Diode Module Fuse)
5.148 Starter Relay
5.149 Kernel Processor Winch Relay (If Equipped)
5.150 Safety Rules When Replacing Halogen Bulbs
5.151 Replace Cab Headlight Bulb (Non-Light Emitting Diode [LED] Lights)
5.152 Adjust Cab Headlights (Non-Light Emitting Diode [LED] Lights)
5.153 Replace Cab Headlights (Light Emitting Diode [LED] Lights?If Equipped)
5.154 Adjust Cab Headlights (Light Emitting Diode [LED] Lights?If Equipped)
5.155 Replace Cab Headlights Halogen Light Bulb (High- and Low-Beam)
5.156 Adjust Cab Headlights Halogen Light Bulb (High- and Low-Beam)
5.157 Replace Cab Headlights (High- and Low-Beam – Light Emitting Diode [LED] Lights?If Equipped)
5.158 Adjust Cab Headlights (High- and Low-Beam – Light Emitting Diode [LED] Lights?If Equipped)
5.159 Replace Fascia or Side Finder Light Bulb (If Equipped)
5.160 Replace Lower Driving or Lower Work Light Bulb (Non-Light Emitting Diode [LED] Lights?If Equipped)
5.161 Adjust Lower Driving or Lower Work Lights (Non-Light Emitting Diode [LED] Lights?If Equipped)
5.162 Replace Lower Driving or Lower Work Lights (Light Emitting Diode [LED] Lights?If Equipped)
5.163 Adjust Lower Driving or Lower Work Lights (Light Emitting Diode [LED] Lights?If Equipped)
5.164 Replace Beacon Light (Light Emitting Diode [LED] Lights)
5.165 Replace Work Lights (If Equipped)
5.166 Replace Service Lights
5.167 Replace Tail, Stop or Turn Lights
5.168 Replace Cab Interior Light
5.169 Replace Map Light
5.170 Replace Toolbox Compartment Light
5.171 Replace Access Ladder Light
5.172 Replace License Plate Light
5.173 Rear Axle Toe-In
5.174 Hydrostatic Drive ? Adjusting Cable (Push-Button Shift Transmission Only)
5.175 Check Brake Fluid Reservoir (Push-Button Shift Transmission Only)
5.176 Check Park Brake Cylinder Cables (Push-Button Shift Transmission Only)
5.177 Brake System
5.178 Active Fill Control System (Option)
5.179 AutoTrac? RowSense? System (Option)
5.180 Additive Dosing System (Option)
5.181 Change Additive Dosing System Nozzle
5.182 Replace XStream KP? Kernel Processor Air Filter Element (If Equipped)
5.183 Replace Fresh Air Filter
5.184 Replace Recirculation Air Filter
5.185 Check Refrigerant Level
5.186 Replace Blower Rear Wear Plates
5.187 Replace Blower Side Wear Plates
5.188 Replace Discharge Tower Wear Plates
5.189 Replace and Adjust Blower Paddles
5.190 Spout Service Opening and Wear Plates
5.191 Swap Discharge Spout Extensions (If Equipped)
5.192 Adjust Spout Motor Gear and Ring Gear
5.193 Adjust Kernel Processor Drive Belt Tension (Machine with Mechanical Belt Idler Only)
5.194 Jacking Points
5.195 Service Tires Safely
5.196 Care and Service of Tires
5.197 Wheel Bolts and Nuts
5.198 Mounting Tires
5.199 Changing Tires
5.200 Tire Sizes
5.201 Required Tire Load Indexes
5.202 Tire Pressures
5.203 Use Genuine John Deere Parts
5.204 Engine Storage Guidelines for Long Term Storage
5.205 Prepare Machine for Storage
5.206 Premium KP? Kernel Processor End-of-Season Maintenance
5.207 XStream KP? Kernel Processor End-of-Season Maintenance
5.208 Remove Machine from Storage
6 Specifications
6.1 8100 Forage Harvester
6.2 8200 Forage Harvester
6.3 8300 Forage Harvester
6.4 8400 Forage Harvester
6.5 8500 Forage Harvester
6.6 8600 Forage Harvester
6.7 8100?8600 Forage Harvesters
6.8 Dimensions
6.9 Type Plates
6.10 Identify Date Code
6.11 Forage Harvester (Machine Identification) Type Plate
6.12 Product Identification Number
6.13 Machine Component Serial Numbers
6.14 Metric Bolt and Screw Torque Values
6.15 Unified Inch Bolt and Screw Torque Values
6.16 UK Declaration of Conformity (United Kingdom Only)
6.17 UK Declaration of Conformity (United Kingdom Only)
6.18 UK Declaration of Conformity (United Kingdom Only)
6.19 EU Declaration of Conformity
6.20 EU Declaration of Conformity
6.21 EU Declaration of Conformity
6.22 Declaration of Conformity
6.23 Eurasian Economic Union?EAC
6.24 Eurasian Economic Union?EAC (English, Russian, and Kazakh)
6.25 Machine Design Life
6.26 Toxic or Hazardous Substances or Elements Disclosure?Image Processing Module (IPM)
6.27 Toxic or Hazardous Substances or Elements Disclosure?Motec Stereo Camera
6.28 John Deere Active Fill Control?Federal Communications Commission (FCC) Notifications to User
6.29 Safety Note Regarding the Subsequent Installation of Electrical and Electronic Appliances and/or Components
6.30 Fluorinated Greenhouse Gas
6.31 Carbon Dioxide Emissions (CO?)
7 Index
8 John Deere Service Keeps You on the Job
8.1 John Deere Parts
8.2 The Right Tools
8.3 Well-Trained Technicians
8.4 Prompt Service